cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
933
Views
0
Helpful
5
Replies

CVP scheduled callback

fabien_damien
Level 1
Level 1

Hello,

 

i'm getting the below error while configuring CCB in a lab in a CVP comprehensive model.

the call flow goes like the following: call manager--->SIP trunk-->voice gateway-->CVP-->ICM

 

172.16.15.78.1421430329246.85.CallbackEntry,01/16/2015 12:45:29.324,Validate_01,custom,Callback_Validate,ELEMENT_ENTRY
172.16.15.78.1421430329246.85.CallbackEntry,01/16/2015 12:45:29.371,Validate_01,custom,Callback_Validate,ELEMENT_ENTRY
172.16.15.78.1421430329246.85.CallbackEntry,01/16/2015 12:45:29.371,Validate_01,element,warning,addXmlBody - Error returned from probe

 

i read similar posts to this one, but no solution was offered except of a successful configuration that was posted online on Cisco website.

Has anybody faced the same issue and was able to know the root cause of the problem?

Any feedback would be appreciated.

 

Thanks.

1 Accepted Solution

Accepted Solutions

deepaul
Level 1
Level 1

Hi Fabien,

Have you configured a sip profile on the gateway ?

Courtesy callback is supported with CUBE (ISR and ASR).

Unified CVP supports ISR 15.0(1)M1.2, 15.1(4)M3, 15.2(2)T, 15.2(3)T1 and 15.2.4 M with the limitations that a "sip-profile" configuration is needed on ISR for the courtesy callback feature.

 

Sample configuration can be found here.

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cust_contact/contact_center/hcs-cc/10_0_1_SU1/Install_config/HCSCC_BK_I8A8633B_00_installing-and-configuring-cisco-hcs/HCSCC_BK_I8A8633B_00_installing-and-configuring-cisco-hcs_chapter_01011.html#HCSCC_RF_RB27A02F_00


In sip-sip configuration the profile is required to send the probe header in the SIP INVITE to CVP.

regards,
Deepu

 

 

 

 

 

View solution in original post

5 Replies 5

deepaul
Level 1
Level 1

Hi Fabien,

Have you configured a sip profile on the gateway ?

Courtesy callback is supported with CUBE (ISR and ASR).

Unified CVP supports ISR 15.0(1)M1.2, 15.1(4)M3, 15.2(2)T, 15.2(3)T1 and 15.2.4 M with the limitations that a "sip-profile" configuration is needed on ISR for the courtesy callback feature.

 

Sample configuration can be found here.

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cust_contact/contact_center/hcs-cc/10_0_1_SU1/Install_config/HCSCC_BK_I8A8633B_00_installing-and-configuring-cisco-hcs/HCSCC_BK_I8A8633B_00_installing-and-configuring-cisco-hcs_chapter_01011.html#HCSCC_RF_RB27A02F_00


In sip-sip configuration the profile is required to send the probe header in the SIP INVITE to CVP.

regards,
Deepu

 

 

 

 

 

Thank you Deepu for your prompt reply, let me give that a try on Monday and will let you know the outcome. 

Thank you Deepu! it worked!

Hi Fabien,

 

Glad that it worked.

 

regards,

Deepu

Reena Mundary
Level 1
Level 1

During lab setup,  I found the same error message as I  missed to call the service cvp-survivability in the coming voip dial peer in the gateway.

 

dial-peer voice 6050 voip

description from gateway

service cvp-survivability

voice-class codec 1

incoming called-number 6050

dtmf-relay rtp-nte h245-signal h245-alphanumeric

 no vad

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: