how to backup UCCE config

[bo liu]

i have a question that how to backup config , awdb or logger?

i backup awdb in AW,and i restore it to the awdb but the logger not sync it..... and i Initialize Local Database in AW the config restore is remove....

whether i should buckup logger???

[Gergely Szabo]

Hi,

it's not absolutely necessary to create a backup of the awdb database, but you must back up the Logger database(s).

What you see is normal. The Initialize Local Database tool deletes everything from the awdb and replaces it with the information taken from the Logger(s). It does not work the other way.

I have written a couple of scripts that dump the following databases:

- Logger A and B

- Outbound Option - BA A

- HDS

- certain registry subtrees from all the servers

Should be enough.

G.

[bo liu]

e...thanks Gergely

i test backup the logger A and restore it and sync to logger B...and use initialize local database tool to sync awdb....i think ...this way is right.....

right?

[bo liu]

not right........when i restore logger A and sync to logger B and sync to AW then i can't open config manager.......

[bo liu]

how should i do the UCCE backup and restore .............

[Gergely Szabo]

Hi,

do you get an error message when trying to start up the Config Manager? If yes, can you post it?

Also, can you post the Distributor logs (turn them up in the registry, dump them, post them to here).

The process you have described (restore Logger A db, sync to B) is fine, then it's perfectly enough to run the Initialize Local Database tool at the AW, it should flush the config and sync the AW database, you don't have to manually sync Logger to AW/Distributor.

G.

[bo liu]

the config manager error -9959

when i run initialize local database tool the error

sorry i dont know hwo to get the logs.....can you tell me how can i do ?

[Gergely Szabo]

Hi,

use the dumplog utility:

http://www.cisco.com/en/US/products/sw/custcosw/ps1001/products_tech_note09186a00800ac599.shtml

I need the EMS traces for the following processes:

- AW:

edt (aw\logfiles)

rpl (dis\logfiles)

uaw (dis\logfiles)

rtd (dis\logfiles)

clgr (dis\logfiles)

rtc (dis\logfiles)

- Logger (everything in la\logfiles):

clgr

rcv

rpl

hlgr

Also, please make sure you are connected to the console session when trying to start up the ConfigManager.

G.

[bo liu]

sorry the aw/logfiles and logger is nothing ....

should i open the trace in regedit?

this is only dis/logiles...

[bo liu]

1

[Gergely Szabo]

Hi,

I don't see anything suspicious there. Replication log shows replication is OK.

Are you sure you are trying to start up the Config Manager from a console session?

G.

[bo liu]

yes...i'm sure....

i find after  i first run initialize local database tool the updateaw is down......never up

[Senthil Kumar Sankar]

hello,

From UAW logs, I could see Recovery Key mismatch, Have you done any kind of importing the config data into the AW Databse ?

04:45:25 dis-uaw Trace: Starting incremental copy operation.

04:45:25 dis-uaw Trace: Recovery keys: 0.0 (in memory), 671735157243.0 (local AWControl), 654644810109.0 (router AWControl).

04:45:25 dis-uaw Trace: Recovery keys: 671735157243.0 (in memory), 671735157243.0 (local AWControl), 654644810109.0 (router AWControl).

04:45:25 dis-uaw Trace: The central log does not match.  Must initialize local database.

Regards,

Senthil

[bo liu]

i use VMware

the ICM is VM.....and i backup the VM have been half year....now the PG connection has change.....

whether is this reason??

e..like:

the ICM connect one CVP before i backup the VM

and now the ICM connect two CVP use tow PIM for HA....and so on...

[bo liu]

1