cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1067
Views
0
Helpful
2
Replies

License IVR Ports.

jmecklenburg
Level 2
Level 2

Hi NetPro

I have a questions for IVR ports and upgrade processes.

When upgrade de IPCC 4.X to UCCX 8.5 Premium, the IVR ports license it's a part number or this port is extracted from DMA Tool?

I see the IPCC DMA tool not export any license.. or not?

Kind Regards.

fixie rider
1 Accepted Solution

Accepted Solutions

anchoudh
Level 9
Level 9

Hi Javier,

You need to provide your UCCX 7.x license as part of the UCRS 4.x to UCCX 7.0 upgrade (you need to provide the path of the UCCX 7.x license during restoring the DMT bacup of 4.x system) using the DMA tool.

DMA tool will not export any licenses as part of the upgrade.

http://www.cisco.com/web/software/282467017/23664/UCCX_DataMigrationTool_Guide_405x-701.pdf

(refer page 27)

http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_7_0/installation/guide/uccx70ig.pdf

And again when you perform W1 (Windows to linux) upgrade from 7.x to 8.5, on 8.5 you need to have the UCCX license based on your license MAC of the hardware.

www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_8_5/installation/guide/uccx851_ug.pdf

You can also contact licensing@cisco.com for further details.

And for your part number queries you can open a case with Partner Helpline team,

please use www.cisco.com/go/ph to do so.

Hope it helps.

Anand

Please rate helpful posts by clicking on the stars below the right answers !!

View solution in original post

2 Replies 2

anchoudh
Level 9
Level 9

Hi Javier,

You need to provide your UCCX 7.x license as part of the UCRS 4.x to UCCX 7.0 upgrade (you need to provide the path of the UCCX 7.x license during restoring the DMT bacup of 4.x system) using the DMA tool.

DMA tool will not export any licenses as part of the upgrade.

http://www.cisco.com/web/software/282467017/23664/UCCX_DataMigrationTool_Guide_405x-701.pdf

(refer page 27)

http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_7_0/installation/guide/uccx70ig.pdf

And again when you perform W1 (Windows to linux) upgrade from 7.x to 8.5, on 8.5 you need to have the UCCX license based on your license MAC of the hardware.

www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_8_5/installation/guide/uccx851_ug.pdf

You can also contact licensing@cisco.com for further details.

And for your part number queries you can open a case with Partner Helpline team,

please use www.cisco.com/go/ph to do so.

Hope it helps.

Anand

Please rate helpful posts by clicking on the stars below the right answers !!

Thanks for you answer!

In the BOM for the upgrade the IVR port is a unique part-number?

Kind Regards.

fixie rider
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: