cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Community Helping Community

7259
Views
0
Helpful
15
Replies
Beginner

UCCX Agent can`t loggin

                  My UCCX is 8.5 su3 ,CME is 8.5.When the IP phone agent loggin ,the screen display "The extension you entered is not associated with this agent ID. Verify the extension and try again"

The CME config in the Attach file.

I have creat agent on UCCX server.

         I have read the Cisco Unified CallManager Express System Administrator Guide,Cisco Unified Contact Center Express Solution Reference Network Design Guide.But I can't find out how to handle this problem.

www.jpg

Everyone's tags (3)
1 ACCEPTED SOLUTION

Accepted Solutions
Engager

UCCX Agent can`t loggin

Hi,

I hope you are using the compatible CME IOS image,

http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_compatibility/matrix/crscomtx.pdf

->Details of CME/IOS version mapping can be found at

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/33matrix.htm

->Only SCCP Phones are supported as Agent Phones with Unified CME. Refer to "Cisco Unified IP Phone Support" section from the respective Cisco Unified CME

Supported Firmware, Platforms, Memory, and Voice Products web page. For example, for Cisco Unified CME 7.1, go to: http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/cme71spc.htm, and scroll down to view the "Cisco Unified IP Phone Support" table.

c. Cisco IP Phones 6911, 6921, 6941, 6945, 6961, 8961, 9951, 9971 are not supported as Agent Phones with Unified CME

If everything is ok and you are still facing the issue, than I would suggest you to appraoch TAC for further help.

Thanks,

Anand

View solution in original post

15 REPLIES 15
Highlighted
Cisco Employee

UCCX Agent can`t loggin

Hi Pengcheng,

Make sure the Agent ID you enter is the correct ID. It is case sensitive. Also, are you using octo lines or dual lines for Agent extensions in CME?

Can you attach a screenshot of the error and share Agent ID with us?

Regards

Gurpreet

Beginner

Re: UCCX Agent can`t loggin

Thanks for your information.

The ID password is correct,If I enter a wrong the screen will a different output "Either the agent ID or the password you entered is invalid"

I use octo lines,ephone-dn 14,20,     dual lines  25. All of them don't work.

ephone-dn                ephone             number                     agent-id

14                                8                   5914                         UCC

20                                20                 5920                         johnlee

25                                25                 5925                         PanchoCai

Engager

UCCX Agent can`t loggin

Hi,

Please try performing Directory Resync operation from the CDA (Cisco Desktop Administrator) and see if it helps.

Thanks,

Anand

Beginner

Re: UCCX Agent can`t loggin

Thanks for your help,but agent still can't login.

Engager

Re: UCCX Agent can`t loggin

Hi,

In UCCX with CME deployments any agent can login with any other extensions, so can you try loggiing in with different extensions.

And also on the UCCX users page, please assign any one of the extensions as IPCC extention and try to login.

Thanks,

Anand

Beginner

UCCX Agent can`t loggin

HI ,

I have try many other extensions,but it  dosen't work.

thank you for your all the informations.

Beginner

Re: UCCX Agent can`t loggin

Step 1:

Under User Management, Application User:

Make sure the phone mac address is in the under Controlled Devices.  Your UCCX system account may have a different name but is is generally something like "...rmuser" All your CTI Agents should be within the "Controlled Devices"

Step 2:

Under User Management, End User:

Make sure the user has the following under Permissions Information:

Standard CTI Enabled

Beginner

UCCX Agent can`t loggin

Thank for your help ,but i use ip phone agents,and I try to enabled CTI,the agnet still can't login.

Engager

UCCX Agent can`t loggin

Hi,

Is your CME subsystem is in service, please check it from the UCCX control center.

Validate the UCCX - CME from UCCX.

Is your ephone's are associated with the correct session-server.

Hope it helps.

Anand

Beginner

Re: UCCX Agent can`t loggin

all the subsystem is in service

all of the CME config is ready.

this is the session,auto add by UCCX.

the ephones are associated  with session-server 2.

thank for your help.

Beginner

UCCX Agent can`t loggin

Hi ,

in your CME , please check

Router(config)# sip−ua
Router(config−sip−ua)# presence enable
after that , restart CCX engine in UCCX
i had the same problem and solved this way.
Good luck


Beginner

UCCX Agent can`t loggin

Thank you very much but I have all ready config

Router(config)# sip−ua
Router(config−sip−ua)# presence enable

before,

I re-config it again and restart the UCCX engine ,it still have issue.

Engager

UCCX Agent can`t loggin

Hi,

I hope you are using the compatible CME IOS image,

http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_compatibility/matrix/crscomtx.pdf

->Details of CME/IOS version mapping can be found at

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/33matrix.htm

->Only SCCP Phones are supported as Agent Phones with Unified CME. Refer to "Cisco Unified IP Phone Support" section from the respective Cisco Unified CME

Supported Firmware, Platforms, Memory, and Voice Products web page. For example, for Cisco Unified CME 7.1, go to: http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/cme71spc.htm, and scroll down to view the "Cisco Unified IP Phone Support" table.

c. Cisco IP Phones 6911, 6921, 6941, 6945, 6961, 8961, 9951, 9971 are not supported as Agent Phones with Unified CME

If everything is ok and you are still facing the issue, than I would suggest you to appraoch TAC for further help.

Thanks,

Anand

View solution in original post

Beginner

UCCX Agent can`t loggin

thanks for your informaions.

I have read the document before.so  I upgrade the uccx from 8.5.1.10000-37 to 8.5.1.11003-32(su3).

and downgrade CME from 8.8 to 8.5.

My phone is 7942,7911,7975,all of them is SCCP phones.

may be I shoule call TAC.

CreatePlease to create content
Content for Community-Ad
FusionCharts will render here