10-20-2015 01:42 AM - edited 03-14-2019 03:20 PM
All,
UCCX newbie here...
I have setup a fairly standard IVR with distribution to 2 CSQs using FIFO. As part of the IVR, Option 2 transfers via an Inter-Cluster Trunk to another UCM cluster. There are likely scenarios where the agent answering the call on the other end of the ICT may have to transfer the call back to the originating contact center. What I would like to do is enable priority on the transfer back to the original contact centre using the existing 2 CSQs.
Is this possible and any pointers please?
Thanks
D
Solved! Go to Solution.
10-20-2015 01:55 AM
Hi D,
Please go through the below support forum documents that will guide you in the right direction on how to achieve this.:
https://supportforums.cisco.com/discussion/12583001/uccx-priortizing-queue
https://supportforums.cisco.com/discussion/12555576/uccx-call-priority-based-ani
https://supportforums.cisco.com/discussion/12543246/uccx-call-subflow-set-priority
https://supportforums.cisco.com/discussion/12406316/setting-priority-certain-callers-while-queue
https://supportforums.cisco.com/discussion/11723006/ipcc-85-setting-set-priority-step-script
https://supportforums.cisco.com/discussion/11349776/uccx-priority-call-queuing
Regards
Deepak
10-20-2015 01:55 AM
Hi D,
Please go through the below support forum documents that will guide you in the right direction on how to achieve this.:
https://supportforums.cisco.com/discussion/12583001/uccx-priortizing-queue
https://supportforums.cisco.com/discussion/12555576/uccx-call-priority-based-ani
https://supportforums.cisco.com/discussion/12543246/uccx-call-subflow-set-priority
https://supportforums.cisco.com/discussion/12406316/setting-priority-certain-callers-while-queue
https://supportforums.cisco.com/discussion/11723006/ipcc-85-setting-set-priority-step-script
https://supportforums.cisco.com/discussion/11349776/uccx-priority-call-queuing
Regards
Deepak
10-20-2015 01:56 AM
Thanks Deepak I will give these a read :)
D
10-20-2015 01:58 AM
Hi
You could add a new trigger to the app, then use a 'get call contact info' step to get the called number.
Based on the call hitting that trigger you could then do an 'IF' callednumber=whatever SET PRIORITY=2
Aaron
10-20-2015 02:12 AM
Thanks Aaron. This sounds fairly straightforward and is in my comfort zone. :)
D
10-20-2015 02:18 AM
Aaron,
Could I not just do this using 1 trigger in the application and match the called number?
D
10-21-2015 06:17 AM
A call that is transferred back in will look like a new call to uccx. But, you could check the calling number and confirm it is from an internal device. If your users are in a different route pattern range than your route points. Bump the priority up 1 if the call was from an internal extension.
If the call is an ICD call, then you can set enterprise variables, and just retrieve them when the script gets the call again. If you see a variable has a value, you know it has been their before. I set one of my variables as the priority. Caller comes in again with a value as a priority. I increase the value by one and set the variable to the higher value. Every time a call is put back into a script, they are more important to get help.
I'd suggest looking at the enterprise data and then the calling party mask for every call that comes thru your script.
10-21-2015 06:37 AM
Yes, of course, if the numbers are known. However with moves/changes etc that might be more difficult than just instructing the agents to use a new number. You can even add a task button in CAD to automate the transfer back to the queue to streamline the process.
Regards
Aaron
Please remember to rate useful responses to highlight useful content..
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide