Cisco Intelligent Traffic Director (ITD)is an innovative solution to bridge the performance gap between a multi-terabit switch and gigabit servers and appliances. It is a hardware based multi-terabit layer 4 load-balancing, traffic steering and clustering solution on the Nexus 5k/6k/7k/9k series of switches.
It allows customers to deploy servers and appliances from any vendor with no network or topology changes. With a few simple configuration steps on a Cisco Nexus switch, customers can create an appliance or server cluster and deploy multiple devices to scale service capacity with ease. The servers or appliances do not have to be directly connected to the Cisco Nexus switch.
ITD won the Best of Interop 2015 in Data Center Category.
With our patent pending innovative algorithms,ITD (Intelligent Traffic Director) supports IP-stickiness, resiliency, consistent hash, exclude access-list, NAT (EFT), VIP, health monitoring, sophisticated failure handling policies, N+M redundancy, IPv4, IPv6, VRF, weighted load-balancing, bi-directional flow-coherency, and IPSLA probes including DNS. There is no service module or external appliance needed.ITDprovides order of magnitude CAPEX and OPEX savings for the customers. ITDis much superior than legacy solutions like PBR, WCCP, ECMP, port-channel, layer-4 load-balancer appliances.
ITD provides :
Hardware based multi-terabit/s L3/L4 load-balancing at wire-speed.
Zero latency load-balancing.
CAPEX savings : No service module or external L3/L4 load-balancer needed. Every Nexus port can be used as load-balancer.
Redirect line-rate traffic to any devices, for example web cache engines, Web Accelerator Engines (WAE), video-caches, etc.
Capability to create clusters of devices, for example, Firewalls, Intrusion Prevention System (IPS), or Web Application Firewall (WAF), Hadoop cluster
Resilient (like resilient ECMP), Consistent hash
VIP based L4 load-balancing
NAT (available for EFT/PoC). Allows non-DSR deployments.
Load-balances to large number of devices/servers
ACL along with redirection and load balancing simultaneously.
Bi-directional flow-coherency. Traffic from A–>B and B–>A goes to same node.
Order of magnitude OPEX savings : reduction in configuration, and ease of deployment
Order of magnitude CAPEX savings : Wiring, Power, Rackspace and Cost savings
The servers/appliances don’t have to be directly connected to Nexus switch
Monitoring the health of servers/appliances.
N + M redundancy.
Automatic failure handling of servers/appliances.
VRF support, vPC support, VDC support
Supported on all linecards of Nexus 9k/7k/6k/5k series.
Supports both IPv4 and IPv6
Cisco Prime DCNM Support
No certification, integration, or qualification needed between the devices and the Cisco NX-OS switch.
The feature does not add any load to the supervisor CPU.
ITD uses orders of magnitude less hardware TCAM resources than WCCP.
Handles unlimited number of flows.
Load-balance traffic to 256 servers of 10Gbps each.
Load-balance to cluster of Firewalls.ITDis much superior than PBR.
Scale IPS, IDS and WAF by load-balancing to standalone devices.
Scale the NFV solution by load-balancing to low cost VM/container based NFV.
Scale the WAAS / WAE solution.
Scale the VDS-TC (video-caching) solution.
Scale the Layer-7 load-balancer, by distributing traffic to L7 LBs.
ECMP/Port-channel cause re-hashing of flows.ITDis resilient, and doesn't cause re-hashing on node add/delete/failure.
Hi, I would like to understand how the command "rate-limit auto" works on Nexus 7000 for SPAN. Below its the official explanation from Cisco but it is not clear to me. For example if my destination interface is 10G and the source traffic is...
Team need clarification regarding the power cord for Japan region. Power standard requirement is 100v / NEMA 5-15R Twist in the PDU. Could you please let us know which power cord we need to order.
Currently will be installing Cisco ...
I'd like to know what is the best way to reset one apic to get access to CIMC configuration menu (F8).Is correct to reload the APIC from system>controllers? I've seen that this reloads the APIC controller (not the entire APIC system), but I don't know ...
I have a muti-pod golf router setup. I have some IPv6 enabled machines on my lan that are connected with ACI leaf switches. I need to make them available on Golf. So, question is how do I send an IPv6 advertisement from my ACI to golf. I have collaps...
Hello, We currently have default gateway on ACI with Firewall redirection using service graph.Is there a feature in ACI which verifies the firewall availability? If the firewall is reachable apply the PBR and if not apply ACI contract for the communi...