Good mornning, I have seen that it is not possible to upgrade from DCNM OVA Release 10.2 (1) to 11.0 (1) directlly, first one should be upgrading from 10.2 (1) to 10.3 (1), then from 10.3 (1 ) to 10.4 (2) and finally from 10.4 (2) to 11.0 (1)I find i...
Forum Posts
I am specifying some refurbished hardware for use in a test lab but am struggling to find the difference between the Nexus 3064PQ and 3064X. Looking for the 3064 which has 48 x 10Gbe SFP ports and 4 x QSFP+ slots able to run in 4x10 or single 40gbe m...
Hi, I am looking for a platform that can do static NAT in hardware, Here are the requirements: 1) Up to 512 static one to one NAT entries, NAT translation implemented in hardware, i.e. wire speed NAT translations, we only need static NAT transla...
Hi dear all, recently I got an issue about NX-OS 8.2(1) in 7700 and would like to know some of the policy such as ACL or Route-map doesn't work very well and these rules couldn't filter or redirect traffic as my wish. This is my configurations on F...
I'm confused on the nexus 3548X software upgrade proccess. Following the official upgrade guide, but after software upgrade has completed, I don't know if the bios information is shown correctly to proceed with it. "show install all status" output ...
I'll try keep this simple using pictures... We want to get from this: To this: The basics are: We are consolidating DC locations for this company/branch as part of a bigger picture strategy.No redundancy with switches at either of these sites e...
Hello! I digged around the documentation, but couldn't find the TCAM size and layout for Nexus 31108PC-V (checked here: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/9-x/security/configuration/guide/b_Cisco_Nexus_9000_Serie...
Hi All, I want ask something about OTV, I have multi AED or dual OTV on one site. Assume, the first box with hostname DC-OTV1 and the second box with hostname DC-OTV2. Ok the question is: 1) I know the higher system id is always for ODD vlan, but...
Hi. We are installing a IE-2000U-16TC-GP and adding a separate AC power source connected to the switch:PWR-IE170W-PC-AC. This will allow the 4 PoE ports to receive power.Your problem is that total budget available POE is 65W instead of 170W. Is there...
Hi All, Need some help to find out how to check the number of VSA's in 1000v. Thanks in advance!! Best Regards Ashish Solanki
Hi All, What's the default method of Spanning-tree Calculation of Cost (Pathcost Method Long 32 bits or Pathcost Method Short 16 bits) in Cisco Nexus Switches ? As I understand, if we have > 1 G links in our Architectures (LANs, DCs, ...) and nowad...
Hi guys, come across an annoying issue in my organisation and I can't find anything solid online regarding this. As per the title, I have a Nexus 7K and I'm trying to set the MTU size for a specific interface but get the following error: MTU on L2 in...
Having a bit of difficulty since there are so many options for configuring SNMPv3 on Nexus. So basically I want one user tied to one group with I guess full privledges and another user tied to another group with I guess just limited monitoring (can't...
Hi, Starting to look at our options for a new European data center. We are looking for the latest best practices for connecting two Data Centers. One will be in Chicago (and is up currently) and the other in Germany. We will have a 10G "dark fibe...
Just like traceroute mac works on IOS device , will same feature works on NX-os as well. I have 7k seats on my Core followed by 5k as access/Distribution from there few 3750/2960 Connected down the line, problem is every time when I need to trace ...
