Hi,since december we have the nexus 1000v in our company. Everything working fine and looks good. We have a ESX cluster with two hosts and 7 NICs uplink. Today after a long time i have a look in the logging and saw this:Dropping received frames from ...
Hi,I have a data-centre with three clusters configured. I have installed a Nexus 1000V with Primary / Secondary VSMs in one cluster and all is working well.I have now installed a new 1000v and VSM on the second cluster and have successfully created ...
Hi We are evaluating the NEXUS 1k as we would like to use LACP on the uplinks to our VM-ware hosts. I'm able to configure LACP to the VEM that is on the same host as the VSM. Enabling it on another host with only VEM will bring the interfaces to...
Is it possible to port channel 2 10G ports on the Nexus 1000V (Emulex CNAs) with 2 10G ports on the Nexus 5000 if the ports on the Nexus 5000 ports are also doing FCOE?I am getting the following error:N5k(config-if-range)# int e1/5-6N5k(config-if-ra...
Hi,I'm running into an issue when installing Nexus 1000v VSM on an evaluation copy of the Vcenter Server 4.0 - it does NOT allow me to pick up the server. I'm doing OVF template installation through the vcenter GUI.Does the evaluation version of vCen...
Hi All,I am very new to Nexus1000v. I am trying to install it on Blade server. I have three servers, one with vCenter in vlan 100, other two with ESXi 4.0 have two pNICs. i have installed the VSM in one esx server whose service console in vlan 100 ha...
Hello,Anybody else seen the issue where it takes like 15 seconds to sh a running-config on the 1000v. Fairly annoying for sure. I've seen this in the past and resolved it somehow but not sure. After having an issue and having to rebuild my 1000v it's...
Hi all,I know that we can run script with run-script command in nexus1kv. But how can I write the repeated command in the script? Does nexus1kv support the loop in the script, such as for or while? I can't find the material about it. Thanks in advanc...
Hi all,I tried to install the release 1.2 Nexus 1000V with the new automatic installer. Deployment runs fine, but in the installer, after choosing the VSM VM and assign the VLANs I got the message "the choosen VM does not appear to be a Nexus 1000V V...
Buenos días.Estoy por realizar la compra del Nexus 1000V pero tengo duda entre dos números de parte casi iguales pero con la diferencia de:1.- Nexus 1000V eDelivery CPU License Qty 16 (1YR Min Service)2.- Nexus 1000V Paper CPU License Qty 16 (1YR Min...
There are several commands listed in the troubleshooting guide for VEM health status on ESX hosts from the command line. I'm not having any luck finding any commands that might work over the VMA connecting to ESXi hosts. Does anyone know of any comma...
Hello Allran to the issue while trying to connect to the vcenter:boot kickstart bootflash:/nexus-1000v-kickstart-mz.4.0.4.SV1.3.bin sup-1boot system bootflash:/nexus-1000v-mz.4.0.4.SV1.3.bin sup-1boot kickstart bootflash:/nexus-1000v-kickstart-mz.4.0...
Hi guys,I got an error when i try to establish svs connection between n1000 and vc.n1000v-test(config-svs-conn)# show svs connectionsconnection VC: ip address: 10.0.0.166 protocol: vmware-vim https datacenter name: Calgary DVS uuid: - ...
Newly deployed Nexus 1000v, running two VSMs (HA) and VEMs on two ESXi 4.0 hosts. VSM-VEM communication appears to be okay (we're not running the VSMs on the VEMs), and license status seems to be okay... but the vethernet port used by the first VM i...
