Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
AI can be used to patch datacenter systems that have Cisco gear. AI can be used to automate the patching process, which can save time and resources, and it can also help to ensure that patches are applied correctly and consistently.There are a few di...
I'm currently looking into the possebilties of netconf and ansible with a nexus 9k switch.
I would like to push the config to a "candidate" on the nexus and diff it with the running config. The playbook works, but the config is not pushed to candida...
After a software upgrade, the Cisco switch profile was lost, and I now need guidance on the essential steps and measures to reconfigure the Cisco N5k switch profile to replicate the existing configuration. Please help.
I recently upgraded the Cisco N5K (dual home) along with 11 Fex. Following the switch upgrade, we experienced a loss of the switch profile configuration. Could you please clarify if a Nexus software upgrade, specifically from version 5.1(3)N2(1c) to ...
Does the 9348GC-FX3 support ACI mode? I have not found any information that directly states is does or doesn't support ACI. CCW will only allow me to select NXOS mode and the data sheet for the FX3 family doesn't specify a minimum ACI software requir...
Hi GuysQuestions if y pls?1. still, vPC behaves just as L2 on the newest NX-OS ??? 2. any update on OTV in the latest newest release in NX-OS ? do we still that bunch of config to localize FHRP ? Thanks
So for some.. random reason I have client whom has created all 3967 vlans on two pair of nexus switches, and I am getting the warning trheshold on this that its utilizaion 100 percent of the feature vlans
I get that he has reached maxim allowed v...
Hi Guys DCI Based on N7Ks with OTV , how to design the service layer with F5 and ASA 5585 with IPS Module , do i need pair OF F5 and ASA 5585 in each DC or 1 ASA in DC1 while ASA-2 in DC2 as long as OTV offer L2 Adancecy for ASA Cluster Link same...
Is there something basic I am missing with any of these EEM scripts? I can't get any of them to work. I have tried on a physical 7k and two virtual 9k's running different code.Here is a basic example of where I don't see any syslog being generated:NX...
Hello Team,We are having an issue with one of the chassis.C9407R when I run show environment I can see that Slot SENSOR Current State Reeding Threshold(Minor,Major,Critical,Shutdown)R0 Temp:Coretemp Normal ...
I'm trying to add a ethernet-segment command under a interface, but the switch doesn't recognize the command.
LEAF1.AMS3(config-if)# ethernet-segment 1907^% Invalid command at '^' marker.LEAF1.AMS3(config-if)#LEAF1.AMS3(config-if)# system-mac 0000.0...
I am mocking up putting an HA-Firewall (FTD) pair into a fabric.I am taking the eBGP approach, building a BGP session to the loopback of each VTEP. (see attached diagram)There are no vPC devices.The BGP Session to VTEP 3 comes up just fine, but the B...
Dear all,
It is pretty curious if it configures below and after ping Nexus9K creates AM route. I appreciate if there is any speficiation or tips.
interface Ethernet1/3
medium p2p
ip unnumbered loopback0
ip ospf network point-to-point
ip...
Hello,I have an odd case to work on and trying to figure out the caveats behind the scenes. The setup is EVPN ingress-replication Peer Learning - BGP. -- No IGP underlay, no mcast. !interface nve1 no shutdown host-reachability protocol bgp adverti...
