HelloI'm a junior network engineer and i'm having issues changing the snmp credentials on a 9000 series.I'm trying to change SNMP credentials and get the following error.I don't know what the problem is and can't seem to fix this.Does it expect a has...
We are working on using private vlans with a new firepower device in our DMZ. As you know, firepower does not support private vlans. So we want to use the promiscious trunk feature on the nexus 9300 to reach our goal. Before, we just had a normal tru...
Hi everyone,I would like advice regarding nxos software upgrade in non-ISSU mode for Nexus 5548P. I should update the nxos release of this device, and I would like to estimate the times (minutes..hours ..) it will take to get back up in forwarding. H...
Hi, I'm searching for the latest firmware update ofCatalyst Express 500 SeriesModel-No: WS-CE500-24TT V01 Hope someone can help. Best regards.
Hello All, In the data center, I need to run L2VPN, so I plan to use VxLAN EVPN as the overlay, but I hope that VxLAN EVPN can be forwarded by SR Traffic-eng using Explicit Path. I don’t know if this can be achieved on Nexus 9000 series switches? Doe...
Hi All, Can anyone confirm me about the Cisco Nexus data center 10G switches as what is the main difference between both of them as i need to create vPC and for vPC both should be identical but i am little bit confused about the models or both are sa...
Hi!I am trying to find out how to determine the tail drops on a host interface of a 2232pp fex. When you run the following commands:attach fex xxxfex-xxx# show platform software woodside intsyou get output like:...| SS0 : ssx_int_norm_td ||--+-------...
I have a 3560 switch running 12.2 and I am looking to restore it's configuration to a 9300 running 16.12.4Can I simply use the web GUI to copy the config? I am a novice user and just wanted to make sure this is something that is possible before I go...
Hello guys, Iam trying disable Cisco Device Manager to listening on tcp 80 but it still comes on ip in web browser..I tried apply Access list on mgmt interface and also disable feature http-server on DS-HP-8GFC-K9 (NX-OS) but still is there How to d...
Hi.Server admin is going to deploy RDMA cluster with Win SRV 2016-2019 using iWARP, not RoCE/RoCEv2.He provided a deployment guide with config examples for Cluster Member Hosts and Cisco Nexus switches which these hosts are connected to.This guide sa...
Hi all, We are a university campus that has two sites. On the first site we have a VPC cluster of two N9K 93180YC-EX switches. On the second site we have only one N9K 93180YC-EX. The two sites are interconnected via a direct 10G link and they also ca...
Hi,I have a N9K-C93180YC-FX, nxos.9.3.6.binInterface Eth1/12 has MACsec configured with 10Gbase-LR in it. I placed 1000base-SX in Eth1/11 and connected a cable. The Eth1/11 ended up in an err-disabled state (Ethernet1/11 is down (speed and macsec mis...
HI All , Arista switches are connected to nexus 5k switches and am seeing Tx-Bcst as 100 % on port 1/39 as below. show port-channel traffic interface port-channel 38ChanId Port Rx-Ucst Tx-Ucst Rx-Mcst Tx-Mcst Rx-Bcst Tx-Bcst------ --------- ...
Hello, I am planning to use the module/optics QSFP-40G-SR4 (QSFP to Four SFP+ ) on the Nexus 9536 40G line card. I am assuming that there is no restriction on the 9536 line card as to how many ports and in which order can be setup for 40G to 4 x 10G ...
Hello, I am configuring a brand new Nexus 9000, and I'm worry because I see too many Jumbo Packets on a trunk interface (the only interface I've configured so far). I limited the MTU size to 1500 on this Nexus and on the other peer, but the interface...
