I have seen a number of bug reports on different items why the SNMP daemon could crash. In everyone's experience, what is the common cause of this? I have found so many bug reports, not sure where to start.
Forum Posts
Hi Dear Friend I have question about ip Summrry bgp switch nexusHow summrry Recieved Routes On bgp sessionauto-summrry For Recieved router Or Advertise Route ?
Resolved! Same VLAN as Native and Trunk
Hi All,I faced a very strange issue and I am trying to dig down the exact cause for this. I had deployed new servers and connected them to a stack of 3850s. I tried creating a port-channel and the limitations of server prohibited me from doing so. I ...
Hi guys!I have a simple non-standard topology: Palo Alto, and 2 N9K in VPC domain. ( a diagram you can find in attach). I don't have SPINE in my configuration (pls don't asking me why? . It is non production topology yet, only staging. Between Nexus...
ACL applied on svi IN. Do i need to permit traffic within vlan too? If i allow above will the issue be resolved?or do i need to allow anything else too?
Got an issue trying to point traffic to a firewall.Default route not being advertised to ospf on a pair of Nexus 9k's using VPCPart of config vrf context PUBLICip route 0.0.0.0/0 10.249.9.2 name PUBLIC_VRF router ospf 11default-information originate ...
I have a nexus 93180 that I need to run a traffic test on. Connecting a Tberd traffic tester to an SFP in port 1. In port 3 and 4 are two identical optics connected to each other. Ports 5&6 have another set of two identical optics connected together....
Hi guys!I have a simple topology that consists of the one Palo alto and 2 N9K nexuses (VPC domain). In my case, the topology does not imply a SPINE (don’t ask me why? :-). It is not a production topology, only staging. ( you can find a diagram in...
I have two of the same routes in my routing table, one is OSPF and one is eBGP. I want the OSPF route to be preferred over the BGP route. (The eBGP route will be the backup route when the OSPF route is gone)I configured a BGP route map to apply a hig...
Nexus SW:- NXOS: version 7.0(3)I7(6)This SW has BGP peering with Cloud Vendor 1 , Cloud vendor 2 , Cloud Vendor 3 requirement is :-I would like to advertise routes originated from cloud vendor 1 to cloud vendor 2 and ignore cloud vendor 3 and other ...
I have two Nexus 9000s configured as VPC. I have an ASA firewall with a VPC port-channel to the Nexus switches. I am peering OSPF between the Nexus and the ASA. Both of the Nexus and the ASA are in Area 0. I want to block some routes being installed ...
Posted to Data Centre blogs by mistake, reposting here. I'm having a strange problem redistributing iBGP routes to OSPF on Nexus 9000. Initially I had an open prefix list to get things working. Some of the routes weren't being redistributed to OSPF a...
Hi community, if somebody can explain me. I have two devices that not support LACP and I have two N9K with vPc. How to connect them both on N9K? Thank you.
Hello group,I'm struggling to make the PBR working on Nexus7010 (with SUP2,N7K-M132XP-12L and NX-OS 7.3.3 D1) The setup is the following small MPLS topology: <Customer CE router> --- <Nexus7K MPLS PE> --- <MPLS P router> --- <Egress MPLS PE router1 &...
Hello, After configuring additional ACL entries - we're getting this error message. "ERROR: tcam region full" I wonder if this is true or a bug. If the message says tru - how can i check the TCAM numbers ? Im using older NXOS version, but willing to ...
