cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1442
Views
0
Helpful
2
Replies

Image preload failed on N2K-C2148T-1GE

djspy
Level 1
Level 1

Hi all. i have cisco Nexus5548 Chassis 

Software
BIOS: version 3.6.0
Power Sequencer Firmware:
Module 1: v5.0
Module 2: v2.0
Microcontroller Firmware: version v1.0.0.14
QSFP Microcontroller Firmware:
Module not detected
CXP Microcontroller Firmware:
Module not detected
kickstart: version 7.3(1)N1(1)
system: version 7.3(1)N1(1)
BIOS compile time: 05/09/2012
kickstart image file is: bootflash:///n5000-uk9-kickstart.7.3.1.N1.1.bin
kickstart compile time: 10/5/2016 19:00:00 [10/06/2016 06:33:12]
system image file is: bootflash:///n5000-uk9.7.3.1.N1.1.bin
system compile time: 10/5/2016 19:00:00 [10/06/2016 08:18:55]

And connect N2K-C2148T-1GE

configure fex port and connet by DAC cable

09/10/2020 18:15:39.074431: Image preload failed.
09/10/2020 18:15:40.235905: Deleting route to FEX
09/10/2020 18:15:40.251187: Module disconnected
09/10/2020 18:15:40.251793: Module Offline
09/10/2020 18:17:36.235113: Module register received
09/10/2020 18:17:36.236278: Image Version Mismatch
09/10/2020 18:17:36.236502: Registration response sent
09/10/2020 18:17:36.236676: Requesting satellite to download image

 

Have problem witch updating image on n2k extention

Sombody can help my?

1 Accepted Solution

Accepted Solutions

Sergiu.Daniluk
VIP Alumni
VIP Alumni

8.Starting with Cisco NX-OS Release 6.0(2)N1(1), 2148T FEX is not supported on Cisco Nexus 5500 series devices.

Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/release/notes/7x/Nexus5500_Release_Notes_7x.html#pgfId-770878

If you plan to use first gen FEX (2100) then you will have to downgrade to a NX-OS version lower then 6.0(2)N1(1).

Make sure you read the release notes and upgrade guides before performing the downgrade.

Cheers,

Sergiu

View solution in original post

2 Replies 2

Sergiu.Daniluk
VIP Alumni
VIP Alumni

8.Starting with Cisco NX-OS Release 6.0(2)N1(1), 2148T FEX is not supported on Cisco Nexus 5500 series devices.

Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/release/notes/7x/Nexus5500_Release_Notes_7x.html#pgfId-770878

If you plan to use first gen FEX (2100) then you will have to downgrade to a NX-OS version lower then 6.0(2)N1(1).

Make sure you read the release notes and upgrade guides before performing the downgrade.

Cheers,

Sergiu

thx

return 2148T to saller a get C2248TP

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: