Hi all,
I use a switch profile to keep the configuration of two Nexus 5548 in sync. That always worked. Now I have the problem that the synchronization only works in one direction. Sync from sw2 is ok, sync from sw1 is not ok. I've already tried a few things, maybe someone can help me.
Nexus5548 Chassis ("O2 32X10GE/Modular Universal Platform Supervisor")
kickstart: version 7.3(2)N1(1)
system: version 7.3(2)N1(1)
sw1# sh vpc
Legend:
(*) - local vPC is down, forwarding via vPC peer-link
vPC domain id : 1
Peer status : peer adjacency formed ok
vPC keep-alive status : peer is alive
Configuration consistency status : success
Per-vlan consistency status : success
Type-2 consistency status : success
vPC role : secondary
Number of vPCs configured : 298
Peer Gateway : Enabled
Peer gateway excluded VLANs : -
Dual-active excluded VLANs : -
Graceful Consistency Check : Enabled
Operational Layer3 Peer-router : Disabled
Auto-recovery status : Enabled (timeout = 360 seconds)
sw2# sh vpc
Legend:
(*) - local vPC is down, forwarding via vPC peer-link
vPC domain id : 1
Peer status : peer adjacency formed ok
vPC keep-alive status : peer is alive
Configuration consistency status : success
Per-vlan consistency status : success
Type-2 consistency status : success
vPC role : primary
Number of vPCs configured : 298
Peer Gateway : Enabled
Peer gateway excluded VLANs : -
Dual-active excluded VLANs : -
Graceful Consistency Check : Enabled
Operational Layer3 Peer-router : Disabled
Auto-recovery status : Enabled (timeout = 360 seconds)
sw2 (conf sync is working fine)
sw2# conf sync
sw2(config-sync)# switch-profile Nexus
Switch-Profile started, Profile ID is 1
sw2(config-sync-sp)# interface Ethernet117/1/9
sw2(config-sync-sp-if)# no description
sw2(config-sync-sp-if)# verify
Verification Successful
sw2(config-sync-sp)# comm
Verification successful...
Proceeding to apply configuration. This might take a while depending on amount of configuration in buffer.
Please avoid other configuration changes during this time.
Commit Successful
sw1 (conf sync not working)
sw1# conf sync
sw1(config-sync)# switch-profile Nexus
Switch-Profile started, Profile ID is 1
sw1(config-sync-sp)# interface Ethernet117/1/9
sw1(config-sync-sp-if)# no description
sw1(config-sync-sp-if)# verify
Verification Successful
sw1(config-sync-sp-if)# comm
Verification successful...
Proceeding to apply configuration. This might take a while depending on amount of configuration in buffer.
Please avoid other configuration changes during this time.
Failed to Commit: Commit Failed
sw1# show switch-profile status commit
switch-profile : Nexus
----------------------------------------------------------
Start-time: 771299 usecs after Wed Sep 16 12:06:05 2020
End-time: 394129 usecs after Wed Sep 16 12:06:53 2020
Profile-Revision: 111
Session-type: Commit
Session-subtype: -
Peer-triggered: No
Profile-status: Commit Failed
Local information:
----------------
Status: Commit Success
Error(s):
Peer information:
----------------
IP-address: 10.254.60.240
Sync-status: Not yet merged
Merge Flags: pending_merge:0 rcv_merge:1 pend_validate:1
Status: Commit Failure
Error(s):
Failed command(s):
config terminal
interface Ethernet101/1/1
sw2# show switch-profile status commit
switch-profile : Nexus
----------------------------------------------------------
Start-time: 892447 usecs after Wed Sep 16 12:06:05 2020
End-time: 508829 usecs after Wed Sep 16 12:06:54 2020
Profile-Revision: 141
Session-type: Commit
Session-subtype: -
Peer-triggered: Yes
Profile-status: Commit Failed
Local information:
----------------
Status: Commit Failure
Error(s):
Failed command(s):
config terminal
interface Ethernet101/1/1
Peer information:
----------------
IP-address: 10.254.17.240
Sync-status: In sync
Status: Commit Failure
Error(s):
Failed command(s):
config terminal
interface Ethernet101/1/1