annuler
Affichage des résultats de 
Rechercher plutôt 
Vouliez-vous dire : 
cancel
1203
Visites
5
Compliment
1
Réponses

Routeur 2801 encapsulation

Olipo
Level 1
Level 1

Bonjour

Nous avons un routeur 2801 qui normalement utilise l'encapsulation HDLC.

Le fichier de configuration comprend les lignes suivantes : encapsulation frame-relay IETF
et puis : frame-relay interface-dlci 17

Mon doute est si le routeur a été configuré pour l'encapsulation HDLC, ou bien si l'encapsulation de relais de trames utilise-t-elle l'encapsulation HDLC pour gérer les circuits virtuels par défaut ? Qu'est-ce qui ne vas pas ?

 

Merci de votre support et bon weekend à tous !

Olivier P.

1 SOLUTION APPROUVÉE

Solutions approuvées

luis_cordova
VIP Alumni
VIP Alumni

Salut @Olipo,

 

Vérifiez ce que ce guide indique:

Frame Relay Encapsulation

When Frame Relay encapsulation is enabled on a serial interface, the interface configuration is hierarchical and comprises the following elements:

  • The serial main interface comprises the physical interface and port. If you are not using the serial interface to support Cisco HDLC and PPP encapsulated connections, then you must configure subinterfaces with permanent virtual circuits (PVCs) under the serial main interface. Frame Relay connections are supported on PVCs only.
  • Serial subinterfaces are configured under the serial main interface. A serial subinterface does not actively carry traffic until you configure a PVC under the serial subinterface. Layer 3 configuration typically takes place on the subinterface.
  • When the encapsulation on a serial interface is changed from HDLC to any other encapsulation type, the configured serial subinterfaces on the main interface inherit the newly changed encapsulation and they do not get deleted.
  • Point-to-point PVCs are configured under a serial subinterface. You cannot configure a PVC directly under a main interface. A single point-to-point PVC is allowed per subinterface. PVCs use a predefined circuit path and fail if the path is interrupted. PVCs remain active until the circuit is removed from either configuration. Connections on the serial PVC support Frame Relay encapsulation only.

https://www.cisco.com/c/en/us/td/docs/routers/access/800M/software/800MSCG/serconf.html

 

Salutations

 

 

Voir la solution dans l'envoi d'origine

1 RÉPONSE 1

luis_cordova
VIP Alumni
VIP Alumni

Salut @Olipo,

 

Vérifiez ce que ce guide indique:

Frame Relay Encapsulation

When Frame Relay encapsulation is enabled on a serial interface, the interface configuration is hierarchical and comprises the following elements:

  • The serial main interface comprises the physical interface and port. If you are not using the serial interface to support Cisco HDLC and PPP encapsulated connections, then you must configure subinterfaces with permanent virtual circuits (PVCs) under the serial main interface. Frame Relay connections are supported on PVCs only.
  • Serial subinterfaces are configured under the serial main interface. A serial subinterface does not actively carry traffic until you configure a PVC under the serial subinterface. Layer 3 configuration typically takes place on the subinterface.
  • When the encapsulation on a serial interface is changed from HDLC to any other encapsulation type, the configured serial subinterfaces on the main interface inherit the newly changed encapsulation and they do not get deleted.
  • Point-to-point PVCs are configured under a serial subinterface. You cannot configure a PVC directly under a main interface. A single point-to-point PVC is allowed per subinterface. PVCs use a predefined circuit path and fail if the path is interrupted. PVCs remain active until the circuit is removed from either configuration. Connections on the serial PVC support Frame Relay encapsulation only.

https://www.cisco.com/c/en/us/td/docs/routers/access/800M/software/800MSCG/serconf.html

 

Salutations

 

 

Mise en Route
Bienvenue dans la Communauté !

La communauté est un hub pour vous connecter avec vos pairs et les spécialistes Cisco, pour demander de l'aide, partager votre expertise, développer votre réseau et évoluer professionnellement.
Vous êtes un nouvel arrivant ? Cliquez ici pour en savoir plus.

Nous voulons que votre navigation soit la meilleure, donc vous trouverez des liens pour vous aider à être rapidement familiarisé avec la Communauté Cisco :