ā06-28-2018 01:41 PM - edited ā02-21-2020 07:55 AM
I am trying to deploy Cisco Firepower management center virtual using Cisco_Firepower_Management_Center_Virtual_VMware-VI-6.2.3-83.ovf on esxi 6.7 but I keep getting the error (see the attached). During the steps of choosing files, I chose the ovf file and was asked to choose Cisco_Firepower_Management_Center_Virtual_VMware-6.2.3-83-disk1.vmdk as well. So I did. But I could not continue...
Can someone advise?
Thank you very much!
Solved! Go to Solution.
ā06-28-2018 01:48 PM
Firepower software 6.2.3.x is currently not supported on ESXi 6.7. Here are the currently supported platforms:
Reference: Firepower Compatibility Guide
ā11-20-2019 06:52 PM
The official support of VMware ESXi 6.7 began from the Firepower Version 6.5.
ā06-28-2018 01:43 PM
ā06-28-2018 01:48 PM
Firepower software 6.2.3.x is currently not supported on ESXi 6.7. Here are the currently supported platforms:
Reference: Firepower Compatibility Guide
ā07-06-2018 12:27 PM
thank you
ā03-07-2019 09:26 AM
ā04-12-2019 11:16 AM
Now that Firepower virtual 6.3.0.x has been released, it still appears that vmware esx 6.7 is still not supported. Any update on this?
ā08-14-2019 01:55 PM
When will ESXi 6.7 support FMCv 6.x?
ā08-14-2019 07:44 PM
While it is not officially supported, I can confirm that FMC will install and run just fine on ESXi 6.7.
I have a customer running ESXi 6.7.0 Build 13639324 and I had no issues installing or operating the FMC VM. I started with FMC 6.3.0 and have since upgraded to the latest (currently at 6.4.0.3).
The support listing on the compatibility matrix is a reflection of what Cisco engineering has tested and the TAC will support (only relevant in the event of issues related to the hypervisor). It is sometimes reflective of an innate limitation of the product; but in this case that's not a hard requirement.
ā11-20-2019 08:27 AM
Marvin,
Is it possible that your client started with ESXi 6.5/6.0 and has then since upgraded to ESXi 6.7? I am able to access the FMCv via ESXi 6.7, but previously had FMCv installed on ESXi 6.0. I've attempted a fresh install of 6.4 and tried your suggestion of starting with 6.3 after the migrated ESXi 6.7 upgrade. Both do not allow the hypervisor to continue and gives an error, "Unhandled exception." Cause: Possibly unhandled rejection: {}
ā11-20-2019 06:26 PM
My customer's installation was a greenfield (fresh install) of ESXi 6.7 and FMC.
ā11-20-2019 06:52 PM
The official support of VMware ESXi 6.7 began from the Firepower Version 6.5.
ā11-21-2019 01:29 PM
Nazmul,
Attempted installing FMCv 6.5 (vmdk & esxi ovf) using VMware vSphere web client several times from both Chrome as well as FireFox browsers. I am still getting the same Unhandled Exception Error.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide