12-03-2013 03:37 PM - edited 03-11-2019 08:12 PM
Any help will be great this is all I get from the console. Any suggestions will be great. Everything was woking perfectly!
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45
Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 01 00 1022 2080 Host Bridge
00 01 02 1022 2082 Chipset En/Decrypt 11
00 0C 00 1148 4320 Ethernet 11
00 0D 00 177D 0003 Network En/Decrypt 10
00 0F 00 1022 2090 ISA Bridge
00 0F 02 1022 2092 IDE Controller
00 0F 03 1022 2093 Audio 10
00 0F 04 1022 2094 Serial Bus 9
00 0F 05 1022 2095 Serial Bus 9
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)13) #0: Thu Aug 28 15:55:27 PDT 2008
12-04-2013 12:30 AM
hi lee,
looks like the IOS got deleted or corrupted.
you'll need to upload the IOS via ROMMON/TFTPDNLD by pressing the escape key.
rommon #1> address 192.168.1.1
rommon #2> server 192.168.1.2 <<< YOUR PC WITH TFTP
rommon #3> file
rommon #4> tftpdnld
12-04-2013 02:44 AM
Thanks for taking time to look at this, I dont think i can reach rommon. I get "invalid Key" pressing ESC.
It wint boot any further than shown on the console output. I dont know if it helps but im using putty.
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 01 00 1022 2080 Host Bridge
00 01 02 1022 2082 Chipset En/Decrypt 11
00 0C 00 1148 4320 Ethernet 11
00 0D 00 177D 0003 Network En/Decrypt 10
00 0F 00 1022 2090 ISA Bridge
00 0F 02 1022 2092 IDE Controller
00 0F 03 1022 2093 Audio 10
00 0F 04 1022 2094 Serial Bus 9
00 0F 05 1022 2095 Serial Bus 9
Evaluating BIOS Options ...
Invalid Key: 001B
Invalid Key: 001B
Invalid Key: 001B
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)13) #0: Thu Aug 28 15:55:27 PDT 2008
12-04-2013 03:36 AM
Hi Lee,
what happens to the status light ?
I think you would need to replace the device, still would like to clarify the status light situation when the firewall boots.
Cheers,
Naveen
12-04-2013 01:58 PM
I've got a solid status and power light.
12-04-2013 04:40 AM
Could you try using 'Break' key instead?
Sent from Cisco Technical Support iPhone App
12-04-2013 01:57 PM
Hi, thanks for the help tried that and nothing. Same key error.
12-04-2013 04:39 PM
Ive left it a few hours and ive got this.
Cisco Systems ROMMON Version (1.0(12)13) #0: Thu Aug 28 15:55:27 PDT 2008
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45
Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 01 00 1022 2080 Host Bridge
00 01 02 1022 2082 Chipset En/Decrypt 11
00 0C 00 1148 4320 Ethernet 11
00 0D 00 177D 0003 Network En/Decrypt 10
00 0F 00 1022 2090 ISA Bridge
00 0F 02 1022 2092 IDE Controller
00 0F 03 1022 2093 Audio 10
00 0F 04 1022 2094 Serial Bus 9
00 0F 05 1022 2095 Serial Bus 9
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)13) #0: Thu Aug 28 15:55:27 PDT 2008
i2c_read_word_w_wait() error, slot = 0x0, device = 0x64, address = 134 byte count = 2. Reason: I2C_HOST_BUSY_ERROR
Platform ASA5505
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: