cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Welcome to Cisco Firewalls Community


423
Views
25
Helpful
17
Replies
Beginner

Re: ASDM unable to reach device

Hi @Marius Gunnerud 

Here is outside:

Gateway of last resort is 1.1.1.1 to network 0.0.0.0

S* 0.0.0.0 0.0.0.0 [1/0] via 1.1.1.1, outside
S 4.2.2.2 255.255.255.255 [1/0] via 1.1.1.1, outside
C 1.1.1.1 255.255.255.224 is directly connected, outside
L 1.1.1.1 255.255.255.255 is directly connected, outside

 

Here is outside-backup:

Gateway of last resort is 1.1.1.1 to network 0.0.0.0

S 8.8.8.8 255.255.255.255 [1/0] via 2.2.2.2, outside-backup
C 2.2.2.2 255.255.255.252 is directly connected, outside-backup
L 2.2.2.2 255.255.255.255 is directly connected, outside-backup

 

And here is sho int ip brief:

ASA5506# sho int ip brief
Interface                  IP-Address      OK?      Method Status     Protocol
Virtual0                    127.1.0.1         YES       unset      up         up
GigabitEthernet1/1    1.1.1.1     YES      CONFIG   up         up
GigabitEthernet1/2    2.2.2.2    YES     CONFIG    up       up
GigabitEthernet1/3 192.168.20.1      YES     CONFIG    up       up
GigabitEthernet1/4 192.168.120.1     YES    CONFIG     up      up
GigabitEthernet1/5 10.254.254.1       YES     CONFIG     up     up
GigabitEthernet1/6 unassigned           YES       unset      administratively down down
GigabitEthernet1/7 unassigned           YES       unset      administratively down down
GigabitEthernet1/8 unassigned           YES       unset      administratively down down
Internal-Control1/1 127.0.1.1             YES       unset up up
Internal-Data1/1 unassigned YES unset up up

 

I am going from a 192.168.30.0 subnet to 192.168.20.0 subnet.  Different office, different state.  I rebooted it again last night and still cant reach it.

Thanks,

 

E
Internal-Data1/2 unassigned YES unset up up
Internal-Data1/3 unassigned YES unset up up
Internal-Data1/4 169.254.1.1 YES unset up up
Management1/1 unassigned YES unset up up
NorthVa5506#

 

VIP Advocate

Re: ASDM unable to reach device

Is 192.168.30.0/24 coming in over a VPN connection on the outside interface?  If yes, do you have the command management-access <interface> where interface is the interface name of the interface you are trying to connect to?

You do not have the 192.168.30.0/24 subnet defined in you http list

ASA# sho run http
http server enable
http 192.168.1.0 255.255.255.0 outside-backup
http 192.168.2.0 255.255.255.0 outside

 

If you are accessing the interface with IP 192.168.20.1 then you would need to add the command http 192.168.30.0 255.255.255.0 <interface name> where interface name is the name of the interface you are trying to connect to as well as management-access command I mentioned earlier.

 

--
Please remember to rate and select a correct answer

View solution in original post

Highlighted
Beginner

Re: ASDM unable to reach device

Hi @Marius Gunnerud you are the man.

 

I added the http 192.168.30.0 inside on the target ASA and it worked.

I have ASDM pulled up and I am able to upgrade the image.

 

Thank you very much,

 

E

CreatePlease to create content
Content for Community-Ad
FusionCharts will render here