cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2640
Views
0
Helpful
7
Replies

FTD 2110 FXOS

behrouz6408021
Level 1
Level 1

Hi everyone  ...

i have a Cisco Firepower 2110 , that is running FTD 6.3 with FXOS Version 2.4(1.243)

i would like to upgrade to 6.4 , but when my FMC upgrade to 6.4 version , it cannot detect my FTD with 6.3 version

FTD 2110 is offline in fmc

i think this problem is  because my FTD FXOS version is lower than the FMC compatibility for detect FTD .

how i can upgrade Firepower 2110 FXOS from 2.4 to 2.6 version ?

i know FXOS in FTD 2100 upgraded when major and minor upgrade is done in Firepower .but my FMC cannot detect ftd with 2.4 version ...

7 Replies 7

balaji.bandi
Hall of Fame
Hall of Fame

6.4.X  release noted clearly mentioned

 

Requires FXOS 2.6.1.157 or later build.

Separate upgrade. Upgrade FXOS first.

 

here is the upgrade document :

 

https://www.cisco.com/c/en/us/td/docs/security/firepower/fxos/fxos261/release/notes/fxos261_rn.html#pgfId-141076

 

we have done some upgrades on 4100,  Note : i have not seen any document mentioning 2100 model, so better check before you upgrade

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Abheesh Kumar
VIP Alumni
VIP Alumni

Hi,

I don't suspect its an issue with FTD2100 FXOS version, as per the 6.4 release note 

6.4 FMC can able to manage devices running older version upto 6.1

Please check is there any reachability issue between your FMC & FTD.

 
Version 6.4.0 Manager-Device Compatibility

Firepower Management Center

Version 6.4.0 FMC

can manage

Version 6.1 through 6.4.0.x devices

Version 6.4.0 devices

require

Version 6.4.0 FMC

Firepower Device Manager

Version 6.4.0 FDM

can manage

one FTD device

ASDM

Version 7.12.1 ASDM

can manage

Version 5.3.x through 6.4.0 ASA FirePOWER modules

Version 6.4.0 ASA FirePOWER modules

require

Version 7.12.1 ASDM

 

Hope This Helps

Abheesh

it is log for this problem .

when i want add ftd to FMC ...

i installed another fmc with version 6.3 and i can register ftd to fmc . but with fmc 6.4 i cannot

hi
can you share the output for below command from ftd2110
show managers

Are the FTD & FMC is in same subnet range..??
Are you able to ping FTD from FMC...??

Hi Abhessh

no , they are in different subnets  but they can reach to each other and no any problem about connectivity

there is no any firewall or ACL or any things between them .

there is no any NAT device between them

 

 

Hi,

Try deleting the manager from FTD and add again.

configure manager delete

configure manager add 172.16.10.210 SecretKey

then check show manager shows FMC IP

Then goto FMC, add FTD management IP and SecretKey

 

Hope This Helps

Abheesh

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: