Hi all
I am having problem command not available when I want to enter command nameif. Below are my detail:
I have a 6503E chassis with hardware below in my lab:
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 2 Supervisor Engine 720 (Active) WS-SUP720-BASE SAD075307HA
2 6 Firewall Module WS-SVC-FWM-1 SAD113900WE
3 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL094868UQ
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 000d.6535.f074 to 000d.6535.f077 3.6 8.5(4) 15.1(1)SY Ok
2 0007.0e1c.b7a2 to 0007.0e1c.b7a9 4.2 7.2(1) 4.1(7) Ok
3 0016.4642.59c4 to 0016.4642.59f3 10.2 7.2(1) 15.1(1)SY Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Policy Feature Card 3 WS-F6K-PFC3B SAD112105TV 2.3 Ok
1 MSFC3 Daughterboard WS-SUP720 SAD075308B2 2.12 Ok
3 Cisco Voice Daughter Card WS-F6K-VPWR-GE SAL09486TTP 1.1 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
I managed to create session to my FWSM with :
session slot 2 processor 1
FWSM show version:
FWSM Firewall Version 4.1(7) <system>
Device Manager Version 6.2(2)F
Compiled on Wed 07-Sep-11 13:35 by fwsmbld
FWSM up 21 mins 12 secs
Hardware: WS-SVC-FWM-1, 1024 MB RAM, CPU Pentium III 1000 MHz
Flash TOSHIBA THNCF128MBA @ 0xc321, 20MB
0: Int: GigabitEthernet0 : address is 0018.7476.d380, irq 5
1: Int: GigabitEthernet1 : address is 0018.7476.d380, irq 7
2: Int: EOBC0 : address is 0000.1200.0000, irq 11
The Running Activation Key is not set, using default settings:
Licensed features for this platform:
Maximum Interfaces : 300
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Cut-through Proxy : Enabled
Guards : Enabled
URL Filtering : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
BGP Stub : Disabled
Service Acceleration : Disabled
VPN Peers : Unlimited
Serial Number: SAD113900WE
Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000
Configuration last modified by enable_15 at 05:04:58.217 UTC Sat Jan 1 2000
nameif command not available at interface
FWSM(config)# interface vlan 10
FWSM(config-if)# nameif inside
^
ERROR: % Invalid input detected at '^' marker.
FWSM(config-if)# ?
Interface configuration commands:
asr-group Configure Asymmetrical Routing group id
default Set a command to its defaults
description Interface specific description
exit Exit from interface configuration mode
help Interactive help for interface subcommands
no Negate a command or set its defaults
shutdown Shutdown the selected interface
FWSM(config-if)#
It also not available at global config
FWSM(config)# nameif vlan10 inside ?
ERROR: % Unrecognized command
FWSM(config)# nameif vlan10 inside security 100
^
ERROR: % Invalid input detected at '^' marker.
FWSM(config)#
I tried to search around and found 1 or 2 discussion here without solved.
Is there anybody know whats wrong and hint on how to fix this?
Thank you in advance.
