Is it possible to two or more public IP Addresses bound to a Cisco ASA 5505 running 8.4(2). If so, how?
Thanks in advance for your help with my request.
i am not really sure about your question, are you talking about assigning multiple ip's to the outside interface of the ASA, if that is the case, then on the ASA interface you can assign only one public ip, not multiple.
Yes, that is what I am talking about. I want to use my Cisco ASA to put a several servers behind the firewall in a DMZ. The outside interface of my Cisco ASA is a public IP address and I want to put several servers which have have public IP addresses in the DMZ behind out firewall. Is this possible?
What I know is you cannot assign multiple ip addresses on your asa outside interface or even on you inside and dmz interfaces unless you will be using VLAN but this will result on different network.
If you want to put or publish your server, first you must do is check if your ISP give you a block of IP Add (/28 /29) and you can use this IP Add to map to your dmz servers. Actually, you can use a single ip add to map it to your dmz servers using port mapping.
i want to configure two server on Asa 5505 with a different IP public.
i got a range of IP address, and i configure the two server. i'm using the asdm launcher.
10.32.1.220 to ip public 188.8.131.52
10.32.1.221 to ip public 184.108.40.206
want to make the NAT
who can help me,
I would recommend the following:
Please, rate helpful answers
Group we are looking to do something similar. We currently have a /29 on the public interface. ISP gave us another /28 which we would like to use. The issue we are having is the current IP's 207.10.X.X are mapped to the Outside interface. We would like to use the same interface for the new block in addition. We have created a NetObj 40.131.X.X which we will use for NAT to internal server. How do we get the traffic from the web to hit NAT?
Regards and thanks for any direction.
Hi, I have to assigned single private IP address on two interfaces of ASA. Previously we are using L3 VLan but in new IOS we cant configured L3 Vlan.
So could you please let me know if its possible now ?
ASA Model : ASA5516 IOS: 9.8(3)29
Yes, if you want to publish several servers behind the firewall, then it is very much possible to nat them on the ASA, lets say you have a block of public ip's from the ISP, then:
static (dmz,outside) 220.127.116.11 10.1.1.1
static (dmz,outside) 18.104.22.168 10.1.1.2
static (dmz,outside) 22.214.171.124 10.1.1.3
static (dmz,outside) 126.96.36.199 10.1.1.4
This is how you do it.
Let me know if you have anymore confusion.
Then they would lose their public IP Addresses would they not? If one wanted to keep their public IP addresses in the DMZ is that possible? Is this a limitation of the 5505? And yes the veil of ignorance is slowly being removed and the confusion is subsiding.
Years ago, when using a Netscreen 204, I believe we were able to have 64 IP addresses bound to the outside interface. Then again, maybe it was a routing issue where the ISP's router routing table pointed all of our IP Address to the outside interface of our firewall.
My company is using a 6509 which sits between the ISP's routers and the rest of our networks. Does that matter or change anything?
All the best!
Ohhhhhh....I guess I get it, correct me if I am wrong, you want to directly assign public ip on the dmz servers itself, rather than natting the public ip to the private ip on the server, well yes, it is very much possible, but there are two conditions:
1. The public ip range for the dmz server should be totally different subnet than the one that is used for the outside interface.
2. The ISP should route the second subnet of public ip's as well to be routed to your firewall.
So if you're outside interface IP is 188.8.131.52
dmz sgould be a different public ip range 184.108.40.206
This is because you can not assign to public ip's of same range on the two interfaces on ASA.
and then lets say you assign a static ip on a server in dmz as 220.127.116.11
so the config on firewall woudl be
static (dmz,outside) 18.104.22.168 22.214.171.124
and it woudl definitely work for you.
Hope this helps
Hope this post could reach you since this thread is 4 years old. So I have 2 public IP segments from my ISP. And I have used all IPs from the first segment and want to utilize the second one. How can I achieved this since ASA can't assign 2 IPs on same interface (outside)? I have tried adding NAT rules using the second IP segment but it doesn't work (my DMZ servers can't be reached from outside).
Please help me out on this.
you don't need to assign multiple IP-addresses - the trick is the MASK besides that you tell ASA where to find the default gateway.
The rest is icing on a cake, and you achive this with the help of NAT.
Lets say you're provided a network with a mask of 255.255.255.248, then nets, or subnets, jump on the number 8.
Lets take the 3rd example here, and configure the outside interface with a mask of 255.255.255.248 and the address of X.X.X.18 (the first usable besides the DFGW), or X.X.X.22 (the last usable if 17 was taken by the DFGW) - we stick with 18.
That all works through 1 cable, 1 interface assigned with the right MASK
Hope that clears the skys?
Pls, rate right answers!