cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Welcome to the Cisco Small Business Community

Have a question? Click on a topic board below to get started in the community.
Get the latest news in this issue of the Cisco Small Business Monthly Newsletter

426
Views
0
Helpful
4
Replies
Highlighted
Beginner

keine Internetverbindung 886w

Hallo, habe gerade den 886w bekommen. Irgendwie will der aber nicht ins Internet. Ich bin leider ganz neu bei Cisco, daher habe ich bezüglich IOS noch nicht viel Erfahrung. Solch eine Konfig habe ich mal zusammengebastelt. Was ist daran noch zu ändern, damit die Internetverbindung klappt.

Meine Config hier als Anhang

! Last configuration change at 23:27:18 CEST Fri Jul 7 2017 by admin version 15.1 no service pad service timestamps debug datetime msec service timestamps log datetime localtime no service password-encryption ! hostname cisco886w ! boot-start-marker boot-end-marker ! ! enable secret 4 8vUBIrgRcyC9okBVecJKVfrUugplMjvqcZzdSzIbcZg ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 clock timezone CET 1 0 clock summer-time CEST recurring last Sun Mar 2:00 last Sun Oct 3:00 service-module wlan-ap 0 bootimage autonomous crypto pki token default removal timeout 0 ! ! ip source-route ! ! ! ip dhcp binding cleanup interval 600 ip dhcp excluded-address 192.168.100.1 192.168.100.149 ip dhcp excluded-address 192.168.100.181 192.168.100.254 ! ip dhcp pool local network 192.168.100.0 255.255.255.0 default-router 192.168.100.254 dns-server 192.168.100.254 domain-name leopold.slikk ! ! ip cef no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO886W-GN-E-K9 sn FCZ1436C2BD license boot module c880-data level advipservices ! ! username admin privilege 15 password 0 secret ! ! ! ! ! ! ! ! ! ! ! interface BRI0 no ip address encapsulation hdlc shutdown isdn termination multidrop ! interface ATM0 no ip address no atm ilmi-keepalive ! interface ATM0.1 point-to-point pvc 1/32 pppoe-client dial-pool-number 1 ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 no ip address ! interface wlan-ap0 description Interface_management_wlan ip unnumbered Vlan1 arp timeout 0 ! interface Wlan-GigabitEthernet0 description Internal switch interface connecting to the embedded AP no ip address ! interface Vlan1 description local_lan ip address 192.168.100.254 255.255.255.0 ip nat inside ip virtual-reassembly in ip tcp adjust-mss 1452 ! interface Dialer0 description DSL-Dialup ip address negotiated no ip redirects no ip proxy-arp ip mtu 1492 ip nat outside ip virtual-reassembly in encapsulation ppp dialer pool 1 dialer-group 1 no keepalive ppp authentication pap callin ppp pap sent-username password 0 ppp ipcp dns request ppp ipcp mask request ppp ipcp route default no cdp enable ! ip forward-protocol nd no ip http server no ip http secure-server ! ! ip dns server ip nat inside source list 101 interface Dialer0 overload ip nat inside source static tcp 192.168.100.152 4662 interface Dialer0 4662 ip nat inside source static udp 192.168.100.152 4672 interface Dialer0 4672 ! ip access-list extended outside-in permit tcp any any eq 4662 permit tcp any any eq 4672 ! access-list 101 permit ip 192.168.100.0 0.0.0.255 any dialer-list 1 protocol ip list 101 ! ! ! ! ! ! ! control-plane ! alias exec zumwlanap service-module wlan-ap 0 session ! line con 0 no modem enable line aux 0 line 2 no activation-character no exec transport preferred none transport input all line vty 0 4 login authentication local_auth transport input telnet ssh ! end

Gruß pcfan1234
Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Participant

You  are missing default

You  are missing default route in your configuration

ip route 0.0.0.0 0.0.0.0 Dialer0

View solution in original post

4 REPLIES 4
Highlighted
Participant

You  are missing default

You  are missing default route in your configuration

ip route 0.0.0.0 0.0.0.0 Dialer0

View solution in original post

Highlighted
Beginner

thank you for the fast answer

thank you for the fast answer. I added this line of code to my global config, but the router still cnnot ping 8.8.8.8 from the telnet interface. The DSL-light is turned on, but the Data light is blinking in an 1-second interval.

Highlighted
Participant

Is IP address present on

Is IP address present on dialer interface?

show ip interface brief

Highlighted
Beginner

I made an mistake while

I made an mistake while typing my password for the Dialup. Only the default Route was missing.

CreatePlease to create content
This widget could not be displayed.