Boot from USB ISE 1.4 in Appliance 3315

[nstr1]

I have an ISE 3315 and I want to update it to version 1.4 but I want to do it from a USB, I found this guide.

http://www.ciscozine.com/install-cisco-ise-usb-cimc/

But it does not come that word I must replace for the 3315 appliance.

Does anyone know what word should I replace ???

Also choose to do it through CIMC but I do not know if the 3315 appliance has this function, the appliance 3315 has the function 3315 ???

And also try to change the boot options and I do not see any option for USB, how can I boot from the USB ???

[RichardAtkin]

CIMC was introduced on the 34xx range so you don’t have that option.

Personally I’ve had trouble with the USB approach but burning an ISO to a DVD works every time... just make sure you have a dual-layer disk as the files sizes are quite large.

Also the 3315 is EoL so you might want to consider upgrading to something newer; this HW will only support up to ISE v1.4, which is also EoL.

[nstr1]

what method do you use to boot from the USB ??, what happens is that it is very difficult to find the double layer disc

[hslai · Accepted solution]

That guide you linked to is done for ISE 2.2 so would not apply to ISE 1.4.

If you want to try USB, then see Create a Bootable USB Drive.

ISE 3315 is IBM 3250M2 but not based on UCS so it does not support CIMC. You might be able to use other KVM solution for mounting an ISO file.

[nstr1]

I am already updating my appliance but now it shows me the following message;

Running anaconda 13.21.215, the Cisco Identity Services Engine system installer - please wait.
*****
***** Detected Cisco UDI (Unique Device Identifier):
***** PID: ISE-3315-K9 , VID: X.X.X, SN: X.X.X.X
***** Hard disk(s) total size detected: 500 Gigabyte
***** Physical RAM size detected: 4052936 Kbytes
***** Number of network interfaces detected: 2
***** Number of CPU cores detected: 4
***** Clock speed of CPU in MHz: 2666
***** Verifying RAM requirement...
***** Verifying NIC requirement...
***** ERROR: THE INSTALLER REQUIRES AT LEAST 4 NICS FOR THIS APPLIANCE TYPE
***** Exiting installation...

***** Verifying Hard disk(s) requirement...
terminating anaconda...done
Anaconda died after receiving signal 15.
sending termination signals...done
sending kill signals...done
disabling swap...
unmounting filesystems...
/mnt/runtime done
disabling /dev/loop0
/dev/pts done
/mnt/stage2 done
/selinux done
waiting for mdraid sets to become clean...
halting system
System halted.

what should i do ??

[nstr1]

I am already updating my appliance but now it shows me the following message;

Running anaconda 13.21.215, the Cisco Identity Services Engine system installer - please wait.
*****
***** Detected Cisco UDI (Unique Device Identifier):
***** PID: ISE-3315-K9 , VID: X.X.X, SN: X.X.X.X
***** Hard disk(s) total size detected: 500 Gigabyte
***** Physical RAM size detected: 4052936 Kbytes
***** Number of network interfaces detected: 2
***** Number of CPU cores detected: 4
***** Clock speed of CPU in MHz: 2666
***** Verifying RAM requirement...
***** Verifying NIC requirement...
***** ERROR: THE INSTALLER REQUIRES AT LEAST 4 NICS FOR THIS APPLIANCE TYPE
***** Exiting installation...

***** Verifying Hard disk(s) requirement...
terminating anaconda...done
Anaconda died after receiving signal 15.
sending termination signals...done
sending kill signals...done
disabling swap...
unmounting filesystems...
/mnt/runtime done
disabling /dev/loop0
/dev/pts done
/mnt/stage2 done
/selinux done
waiting for mdraid sets to become clean...
halting system
System halted.

what should i do ???????