cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Announcements
Choose one of the topics below to view our ISE Resources to help you on your journey with ISE

This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.

75
Views
0
Helpful
3
Replies
Cisco Employee

Link status command on ISE2.4

Sorry for the quick question. But now I can't find ISE command to check interface link status.

For example, now eth1(gigabitEthernet 1) stays admin:up, link status:down

 

C:\>snmpwalk -c ro -v 2c 192.168.10.1 1.3.6.1.2.1.2.2.1.2.3
IF-MIB::ifDescr.3 = STRING: eth1
C:\>snmpwalk -c ro -v 2c 192.168.10.1 1.3.6.1.2.1.2.2.1.7.3
IF-MIB::ifAdminStatus.3 = INTEGER: up(1)
C:\>snmpwalk -c ro -v 2c 192.168.10.1 1.3.6.1.2.1.2.2.1.8.3
IF-MIB::ifOperStatus.3 = INTEGER: down(2)

 

In the situation, "show interface" still shows the interface is UP.

 

ISE/admin# show interface gigabitEthernet 1
GigabitEthernet 1
        flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet 192.168.11.1  netmask 255.255.255.0  broadcast 192.168.11.255

 

Does anyone know good command to check the link status(ifOperStatus) on ISE?

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: Link status command on ISE2.4

On ISE VM, I often see the output of "show interface" not reliable. Since you are able to good results via SNMP, that would be the way to go.

View solution in original post

3 REPLIES 3
VIP Advocate

Re: Link status command on ISE2.4

I just walked a 2.4 node and those mibs indicate up/up for the loopback, and gigabit0 (eth0) which are the only active interfaces.

.1.3.6.1.2.1.2.2.1.2.1 = STRING: "lo"
.1.3.6.1.2.1.2.2.1.2.2 = STRING: "eth0"
.1.3.6.1.2.1.2.2.1.2.3 = STRING: "eth1"
.1.3.6.1.2.1.2.2.1.2.4 = STRING: "eth2"
.1.3.6.1.2.1.2.2.1.2.5 = STRING: "eth3"

.1.3.6.1.2.1.2.2.1.7.1 = INTEGER: 1
.1.3.6.1.2.1.2.2.1.7.2 = INTEGER: 1
.1.3.6.1.2.1.2.2.1.7.3 = INTEGER: 2
.1.3.6.1.2.1.2.2.1.7.4 = INTEGER: 2
.1.3.6.1.2.1.2.2.1.7.5 = INTEGER: 2

.1.3.6.1.2.1.2.2.1.8.1 = INTEGER: 1
.1.3.6.1.2.1.2.2.1.8.2 = INTEGER: 1
.1.3.6.1.2.1.2.2.1.8.3 = INTEGER: 2
.1.3.6.1.2.1.2.2.1.8.4 = INTEGER: 2
.1.3.6.1.2.1.2.2.1.8.5 = INTEGER: 2

Cisco Employee

Re: Link status command on ISE2.4

Yes, SNMP query shows both admin and link status but now "show int" seems to show only admin status.

So I'd like to know if other useful way to show the link status on ISE unit (by CLI command or GUI menu)

Cisco Employee

Re: Link status command on ISE2.4

On ISE VM, I often see the output of "show interface" not reliable. Since you are able to good results via SNMP, that would be the way to go.

View solution in original post