I am testing an SFTP get job to an external site, I get the following message;
FTP JOB Failed : No known hosts provided - use SecureFTPConnection.KnownHosts to add some (safe), or set ServerValidation to None (unsafe).
Is this referencing a file I need to add site info for? What am I missing?
What are you running? 6.x or 5.3.1?
In 5.3.1, It looks like you are chosing the "Private Key File" option under the "Authentication Type". This is on the FTP tab. If your not doing SSH SFTP then you don't need this option. Best to use "User/Password"
But if you are doing SSH SFTP then you'll need to generate a key, point to your private key and send to the client your public key. It is almost the same concept as PGP, but at the SSH level. (i just went through this process and it was very painful. I needed to upgrade from 188.8.131.524 to 184.108.40.2068 first and update our UNIX agent to
220.127.116.11 in order to get that to work.)
The example below is for User/Password option.
For the run tab, I use the following:
Agent (local host) = Our UNIX box agent. UNIX boxes have FTP services installed on them, talk to your admin to see if it is active and running.
Local User = nothing, blank
FTP Host = the site you are FTPing to like ftpsite.site.com:22 (the 22 or 21 port number is some times needed)
FTP User = the user id you'll log onto the ftpsite with. You'll need to create this user in your "Users" list as a runtime.
For the FTP tab:
Protocol = SFTP
FTP Operation = Get file
Format = ? depends on what you are getting, normally Binary
What is the filename you are picking up. you can even use vaiables. test.file.
New Filename = The name it will be on your server.
Local Path = Where you are puting the file on your server
Remote Path = Where the file is on the ftpsite
Then run. Hope this helps.
Thanks Mike, I am using 6.1. This is an SSH job. I have tried running with user/password or passphrase, with or without the port specified and I get the same output regardless. I am using windows servers as the local host.
I do not have the SSH adaptor but the documentation does not indicate what fucntionality it adds or if this is what I need to complete the setup of an SSH job.
Is anyone using the SSH adaptor for a windows environment, is this required to allow my job to work?
Is this the first time you are performing an SFTP using this Windows Agent?
The default behavior for SFTP changed with the 3.x Tidal agents. In 2.x Tidal agent the default behavior was to not verify Known Host Keys. The defalt behavior for 3.x Tidal agents is to verify Known Host keys. You can change 3.x Tidal agents back to the 2.x behavior with a setting in the tagent.ini file. This is what the message "set ServerValidation to None (unsafe)." is referring to.
In your \Tidal\Agent\bin directory look for file "tagent.ini". Create it if necessary. To not require Known Host Key verification you need to add "SSLVLDCRT=n" to the file. Example file follows:
After making this change, cycle the agent service. Then try your job again.
Thank you Tracy,
Yes this is my first attempt of SFTP with Tidal, I'm fairly new to Tidal.
I did add the line to the tagent.ini file and did get a different message below;
FTP JOB Failed : Failed to recognize key format. Supported formats are OpenSSH, SSH.com and PuTTY.
I am assuming this translates to I need to add an SSH client to the server initiating the job?
Got it to work.
In additional to the tagent.ini file we had to make a few edits to our job syntax, by removing some unrequired "\"'s, and removing the local user- leaving that field blank.
thank Tracy and Michael for all the help!