cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Step-by-Step Configuration and Troubleshooting Best Practices for the NGFW, NGIPS and AMP Technologies A Visual Guide to the Cisco Firepower Threat Defense (FTD)
257
Views
0
Helpful
1
Replies
Beginner

IPS-SSM password recovery

Hi,

 

I have an ASA 5510 with IPS module enabled and i m trying to recover the login credentials, when trying the hw-module module 1 password-reset cmd returned an ERROR: % Invalid input detected at '^' marker. Please advice how can i recover the login and password

 

 

Thank you

 

# sh module 1 details 

Getting details from the Service Module, please wait...

ASA 5500 Series Security Services Module-10

Model:              ASA-SSM-10

Hardware version:   1.0

Serial Number:      JAF14

Firmware version:   1.0(11)5

Software version:   7.0(2)E4

MAC Address Range:  d0d0.fd52.b4ff to d0d0.fd52.b4ff

Data plane Status:  Up

Status:             Up

Mgmt IP addr:       192.168.1.2                                                 

Mgmt Network mask:  255.255.255.0                                               

Mgmt Gateway:       192.168.1.1                                                 

Mgmt Access List:   192.168.1.155/32                                            

Mgmt web ports:     443                                                         

Mgmt TLS enabled:   true                                                        

sh ver

Cisco Adaptive Security Appliance Software Version 7.0(8) 
Device Manager Version 5.0(8)

Compiled on Sat 31-May-08 23:48 by builders
System image file is "disk0:/asa708-k8.bin"
Config file at boot was "startup-config"

 

Hardware:   ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
                             Boot microcode   : CNlite-MC-Boot-Cisco-1.2
                             SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
                             IPSec microcode  : CNlite-MC-IPSECm-MAIN-2.05
 0: Ext: Ethernet0/0         : address is 0024.97f0.433e, irq 9
 1: Ext: Ethernet0/1         : address is 0024.97f0.433f, irq 9
 2: Ext: Ethernet0/2         : address is 0024.97f0.4340, irq 9
 3: Ext: Ethernet0/3         : address is 0024.97f0.4341, irq 9
 4: Ext: Management0/0       : address is 0024.97f0.4342, irq 11
 5: Int: Internal-Data0/0    : address is 0000.0001.0002, irq 11
 6: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 5

Licensed features for this platform:
Maximum Physical Interfaces : Unlimited 
Maximum VLANs               : 25        
Inside Hosts                : Unlimited 
Failover                    : Active/Standby
VPN-DES                     : Enabled   
VPN-3DES-AES                : Enabled   
Security Contexts           : 0         
GTP/GPRS                    : Disabled  
VPN Peers                   : 150       

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted

Hi Hisham, This command is

Hi Hisham,

 

This command is not supported in your softeware version - 7.0(2)E4.  Also IPS module should verision 6 or above.

RRecovering the Password for the ASA 5500 AIP SSM

 

Note To reset the password, you must have ASA 7.2.2 or later.

 

http://www.cisco.com/en/US/docs/security/ips/7.1/configuration/guide/cli/cli_troubleshooting.html#wp1139722 

gfgfg

 

gfgf

 

View solution in original post

1 REPLY 1
Highlighted

Hi Hisham, This command is

Hi Hisham,

 

This command is not supported in your softeware version - 7.0(2)E4.  Also IPS module should verision 6 or above.

RRecovering the Password for the ASA 5500 AIP SSM

 

Note To reset the password, you must have ASA 7.2.2 or later.

 

http://www.cisco.com/en/US/docs/security/ips/7.1/configuration/guide/cli/cli_troubleshooting.html#wp1139722 

gfgfg

 

gfgf

 

View solution in original post

CreatePlease to create content
Content for Community-Ad
FusionCharts will render here