08-09-2014 12:16 AM - edited 03-16-2019 11:41 PM
Dear All
I have VG h323 with 3 analog lines and CUCM version 7.5 , i want to confiure one of analog lines to go to hunt group and the others two going to specific users
down sample configuration for a specific user.
the configuration i did as following below : please see option 1 , option 2
Option1
In Voice gateway
voice-port 0/2/0
connection plar opx 3469
Description ## 22222222##
caller-id enable
!
dial-peer voice 250 pots
destination-pattern 9
port 0/2/0
!
in Call manager
create partition PT-22222222
create CSS CSS-22222222
add this parttion to gatewat CSS to allow to go out side.
route pattern 9.!#
it is right configuration ???
OR
voice-port 3/0
connection plar opx 222
caller-id enable
!
dial-peer voice 110 pots
destination-pattern 9[2569].......
port 3/0
!
dial-peer voice 120 pots
destination-pattern 918.....
port 3/0
prefix 18
!
dial-peer voice 130 pots
destination-pattern 91[0-7,9].
port 3/0
prefix 1
!
dial-peer voice 140 pots
incoming called-number .
direct-inward-dial
!
dial-peer voice 200 pots
destination-pattern 900T
port 3/0
prefix 00
!
in option2 , I dont need to configure Route Pattern in CUCM .
is it right and which one is better and good for troubleshooting option 1 , or option 2 and is there any missimg in configration in option1 , option2
thanks.
Solved! Go to Solution.
08-10-2014 02:13 AM
Hello
For example , i need extension 4001 need to call mobile calls using port 0/0/2. So i need to force call to go out using H323 configuration for a specific port on GW
1)Create PT_Mobile
2)CSS_CallsToFXO
4)under RP 99XXXXXXXXXX - specify route partition "PT_mobile"
on VG
dial-peer voice 100 pots
destination-pattern 99..........
port 0/0/2
forward-digits 10
5)Assign CSS for the ext 4001 and for H323 gateway . dial now from 4001 99XXXXXXXXXX the call go out, if you tried from 4002 as example which not have same CSS - you will be unable to get cal out. You can use also FAC to assign code before dialing outgoing calls , if you need to avoid partitions and CSS.
You can also take a look for the below:-
http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/41887-specific-fxs-call.html
Thanks
please rate all useful ifnormation
08-10-2014 03:51 AM
hello
Look we can do as the below:-
We can assume that you have 3 X ports 0/0/1 ,. 0/0/2 and 0/0/3.
Lets saye 0/0/1 is for huntgroup users , 0/0/2 and 0/0/3 for specific users.
1-under 0/0/1 , you can configure connection plar xxxx /where xxxx is the hunt pilot which will include Hunt list and under HL , the line group which includes all specific users"..
2-For 0/0/2 and 0/0/3 to allow both of them , only used by specific users , You can configure a code for outgong calls to hit port 0/0/2 or 0/0/3 and allow users to put the code before hit outgoing call for specific port. Of example if i need to go out 0/0/2 you can put code 99 , for 0/0/3 98.
3-For incoming calls for port 0/0/1 and 0/0/2 , we can use also connection plar opx and assign a xxxx / where the xxxx the extesnion number for your internal user/
Note:-Other Solution based on calling number as below:-
http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/41887-specific-fxs-call.html
Thanks
please rate all useful information
08-09-2014 11:05 PM
Hi Islam,
Could please give an example how the outgoing can be configured using PT and CSS.
Thanks
08-10-2014 02:13 AM
Hello
For example , i need extension 4001 need to call mobile calls using port 0/0/2. So i need to force call to go out using H323 configuration for a specific port on GW
1)Create PT_Mobile
2)CSS_CallsToFXO
4)under RP 99XXXXXXXXXX - specify route partition "PT_mobile"
on VG
dial-peer voice 100 pots
destination-pattern 99..........
port 0/0/2
forward-digits 10
5)Assign CSS for the ext 4001 and for H323 gateway . dial now from 4001 99XXXXXXXXXX the call go out, if you tried from 4002 as example which not have same CSS - you will be unable to get cal out. You can use also FAC to assign code before dialing outgoing calls , if you need to avoid partitions and CSS.
You can also take a look for the below:-
http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/41887-specific-fxs-call.html
Thanks
please rate all useful ifnormation
08-10-2014 03:28 AM
Hi,
Thanks for the reply.
So it means i need to create another route-pattern for extension 4002 with different access-code etc.
Please confrim.
Thanks
08-10-2014 04:04 AM
Hi Mahmood
Look my friend , you can do the below:-
1) 1st solution
1- All users use access-code 9 who will use port 0/0/1
2-For some specific users , use access-code 99 for 0/0/2 and access-code 98 for port 0/0/3.
2) 2nd solution
Other way which is based on calling number as the below and no need for CSS and partitions or special access code:-
Please take a look for the below:-
http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/41887-specific-fxs-call.html
Thanks
please rate all useful information
08-10-2014 03:51 AM
hello
Look we can do as the below:-
We can assume that you have 3 X ports 0/0/1 ,. 0/0/2 and 0/0/3.
Lets saye 0/0/1 is for huntgroup users , 0/0/2 and 0/0/3 for specific users.
1-under 0/0/1 , you can configure connection plar xxxx /where xxxx is the hunt pilot which will include Hunt list and under HL , the line group which includes all specific users"..
2-For 0/0/2 and 0/0/3 to allow both of them , only used by specific users , You can configure a code for outgong calls to hit port 0/0/2 or 0/0/3 and allow users to put the code before hit outgoing call for specific port. Of example if i need to go out 0/0/2 you can put code 99 , for 0/0/3 98.
3-For incoming calls for port 0/0/1 and 0/0/2 , we can use also connection plar opx and assign a xxxx / where the xxxx the extesnion number for your internal user/
Note:-Other Solution based on calling number as below:-
http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/41887-specific-fxs-call.html
Thanks
please rate all useful information
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: