Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello everybody, If I understood the below article correctly, the Speed Dial function is reserved for the patterns *1 to *199. https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/190/1_0/english/administration/guide/sip/ATA190/a190_agAsup.html ...
We use RingCentral. They have an option that can display the queue name and caller id name, plus many other options.If we have queue number and caller id name selected, the caller id name does not display on the phones. If we have one option selected...
Hi, All our ATA191 stop ringing after 60s and we get a reorder tone. An IP phone that is connected to the same shared line continues ringing. I could not find any parameter related to the maximum ring timer for ATA191. They are on SIP firmware and re...
Had to replace a couple ATA190 with ATA191 but running into a weird situation. The ATA191 are the enterprise version (ATA191-K9). We had one ATA191 that was showing the same behavior but for some unknown reason it ended up registering with CM.We al...
I had to replace an informacast analog adaptor that connected to a Bogan overhead paging system. I was recommended to use ATA 191 as the replacement. This is a ATA191-K9 enterprise device, not MPP.I configured the device in cucm and when analog phone...
Hope someone can help.We have followed the setup instructions for the ATA192, we can make outbound calls with no issues. We can receive 1 call, but cannot receive another call for around 10-15 minutes. The line goes straight to voicemail, the line st...
I recently bought a little used ATA192 second hand. I thought a factory reset was a good place to start so I applied power (but made no other connection). The lights flashed as expected. I then pressed the Reset button. The expected sequence of l...
Hello Cisco heroes, I need your help. I am using it connected to an ATA device, but I am inquiring because faxes cannot be sent to a specific number, 02-123-1234. ARS sound is coming from that number. When a call is made to that number from the phone...
Hello,i am facing some warnings in the ATA191 log: Dec 6 01:47:13 ATA191-MPP local1.warning vsock: fprv_eval_profile_rule(3106) FSTR_CFG_RULE: https://activate.cisco.com/software/edos/callhome/rc?id=$MAU:$SN:$PN&sw=$SWVER Dec 6 01:47:13 ATA191-MPP lo...
Ich habe einen ATA 191 Adapter im Einzelhandel erworben. Dieser hat die Firmware "BOOT-ATA191.12-0-1-2". Der Adapter läßt sich leider überhaupt nicht konfigurieren und es sind auch nicht alle reiter/Menümpunkte vorhanden. Laut unsrem TK Provider benö...
Hello Community,I have a problem with an ATA 192 not registering, so I need your help!In the navigation under "Voice" -> "Information" it says "Registration State: Failed". In the navigation under "Administration" -> "Debug Log Viewer" it says "Warni...
CUCM 12.5ATA 191 is not registering with CUCM, when I checked the ATA web page, found that ATA has MPP firmware "11-1-0MSR3-9", is it possible to change the firmware to on-premise (CUCM), I have not found any documentation specific for ATA 191 regard...
I purchased a ATA190 hoping that I could use it in standalone mode without using CUCM. The firmware is the original 1.1.0 (006). I have read that the web interface with this firmware is not good and I have been trying to upgrade it. The only file tha...
I have have an ATA191-MPP that suddenly started flapping. It is in a blue light emergency phone located on the exterior of a building. I have tried restarting the device several times with not luck.It is connected to an Aruba 5412Rzl2. I can see in t...
Hi, I'm looking a way to change this settings:1 The Ata adds its local ip information to the generated Call-id (generated-string@local-ip) , this is not needed since all it needs is unique generated string for the call. There should be a setting to ...
