Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Everyone,I know we cannot have more than one DHCP server configured in a CUCM cluster but how many IP address a CUCM DHCP server can handle? 40000 IP Phones can be registered in a cluster and 7500 in a single CUCM server.Is that a fair statemen...
HI everyone,I would like to ask... currently I am using CM v11.5. I turned on the phone forwarding on my desk phone (8851) so all calls calling to my ext will forward to my cell.Here is what happen. If someone from outside calls my desk phone number,...
hi all,i just get a little confused between cisco jabber and mobile voice access MVA, as my knowledge is if i have cisco jabber over VPN or in my cell phone that mean i can make calls from my extension, so what the point of mobile voice access if i h...
our system telco-sıp-cube-sip -cucm-sip-third party ivr when the customer call the agent.coulnd,t calling . problem 3 5 time a week and 1 or 2 minutes
Hi I purchased a couple of used CP8865 phones and Im trying to get them working using CUCM 14.0.1.I added the phones in CUCM using their MAC address. According to the log on the phones, they can get their cnf.xml.sgn files. Even though the phones sho...
Hello CommunityI'm facing issue with switching between Route Groups which is prioritize in the Route List, I have 2 prioritized list of available paths (i.e. two PRI connection) in route list when the service outage occurs for the 1st path then the a...
Where is the tertiary Call Manager (subscriber #2) IP address stored on an 88xx phone? Our Publisher and Subscriber 1 are in the same datacenter1, while Subscriber 2 is in datacenter2. We are planning to do maintenance on datacenter1 but want to conf...
Hi, I have 4331 router running SDWAN 17.x image.trying to configure voice but it's not supporting the following 2 comands: allow-connections h323 to sipallow-connections sip to h323 Call flow: PSTN >> FXO on router >> CUCM while I have FXO with ana...
My organization recently upgraded our CUCM and CUC from 10.5 to 12.5. We have a mix of 7900 series phones (running on SCCP) and 7800/8800 series phones (running on SIP). Prior to the upgrade, DTMF worked on all phones. After the upgrade, DTMF tone...
Hi,is there a way to enable mobility for all users bulk other than using cucm , And second question for a remote destination profile for snr requires any type of license Thanks
Hoping someone can fill in a hole for me. I am attempting to setup autoenrollment of the user certificate for wireless access for a set of 8865s. I have used the Cisco IP Phone 8861 and 8865 Wireless LAN Deployment Guide to the best of my ability, ...
Hi BoardI have problems getting an MP112 (Audiocodes) to register on a CUCM server. I have configured a user on the CUCM platfom, and a third party SIP device (Advanced). Assigned a new SIP security profile specifying that digest user should be used....
Hello, We have CUCM>>>> VOICE GATEWAY>>>>>>PSTN Inbound calls to pilot number "08039055000" is working fine but calls to the direct lines i.e "08035095207" is not working. I did a dna and attached is the outcome. Kindly advise on what to do
We have a Cisco CIPC 8.6.6 always having problems when changed the laptop from win10 to win11 version. Calls are dropping in the middle of the calls. But not for every call only few calls it's dropping. It is occurring randomly. Please help me better...
Good afternoon,We are currently running CUCM 12.5 with voice gateways and onsite PRI's. We are wanting to move to an internet based SIP Trunk so we no longer need the voice gateways and PRI's. After talking to VM Cisco Rep we bought a Cisco CUBE as w...
