Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Can UCM BE 6 be installed on any MCS or only the MCS-7828?
Is it possible to set the Call ID name for outbound calls from CCM/CUCM. I've read that the Alerting Name on a device's line specifies the Call ID name, but am looking for clarification.Obviously, this depends on our carrier passing whatever we send...
Hi,Is it possible to integrate a Cisco Unity Express (NM-CUE module inside a CME) with a CUCM ?if yes, how do I have to configure my router :- in CME mode ?- in SRST mode ?- in CME in SRST mode ?Thanks in advanceOlivier
hi to all,I want to add a new subscriber into a cluster, i have a cucm 7 Publisher, i add the server on it and then i install the subscriber but when i put the data of the CUCM 7 fails, if i ping the subscriber from the Publisher is ok.Need some help...
What does it mean "Rejected" in CUCM 6?In Callmanager 4 I saw only Registered/Not registered messages?
Customer would like to have PSTN caller-id displayed on their Remote Destination Devices such as cell phones.To elaborate we have CM6.1.2 and H323 PRI with Mobile Connect Enabled at Company ABC. If a PSTN call from company XYZ comes into company ABC ...
Hi,I would like to use CCM Express as a CUCM Fallback using CCME/SRST Functionnality.But I would like to configure by myself ephone and ephone-dn (not using auto provision).The point is when I try to create an ephone-dn, it is always up (show dial-pe...
Dear all,I would like to add an AASTRA MX-ONE Telephony Switch (formerly Ericsson) as a H.323 gw to a Cisco Unified Call Manager 6.1.2. Unfortunatelly this does not work for me. I can make calls from an Ericsson phone to a Cisco IP Phone. The IP Phon...
Hello,Can you help me with my problem? I have setup a DN that when called from outside the office, the call will be forwarded to Cisco MeetingPlace via on-net and when the WAN is down, the call will failover to PSTN (off-net). When I called the DN ...
Hi,last week I upgraded a CUCM server from 5.1(3) to 6.1(2).Now I do have some issues with VG224 (doorbells).The VG224 are connected via MGCP.IPhone - VG224 - AnalogPhone (doorbell)Send “0#†---->>>If I am connected to the doorbell - I should be ...
I've never enabled MAD to CUCM LDAP integration before.I've read as many of the design docs but still have some questions.1. When syncronization happens the first time and the local CM DB is populated, it says all users that don't have a attribute ma...
Is there any application to monitor the System/Server health for CUCM? such as CPU/MEM/HD?We are using sitescope and i am not sure if I can put it on CUCM server.
CUCM 6.1.2.1000-13In CAR, when I go to System > System Parameters > Gateway Configuration I recieve the following error:10011 - System Error. Contact System Administrator. I also get this error when I try to run Gateway Utilization Reports.I can sea...
Hi all we are running cucm 4.3.2 sr 1 with unity 5.01. If user a is on ext 5555 and recieves a second call, the second call is sent the v/m for 5555 but hears the standard greeting, not the busy. In cucm call forward busy for ext 5555 is checked a...
I have a question regarding Cisco Unified Communication Manager 6.1 upgrade, we have customer already order to upgrade from CUCM 4.2.3 to CUCM 6.1.2.I know about this upgrade that system will check for the current number & type of connected IP Phones...
