Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,I have configured the voicemail for user to receive email notification. User able to receive email notification. but instead of only one email which is voicemail email,user also receive voicemail count email. Is there a way to disable voicemail...
Hello, Cisco CME 14.1 transfer call from my local phone to mobile phone dont work. i can hear ringing but local phone wont to forward call to my mobile phone. Does anybody have idea what can be problem. Log 648585: Mar 22 15:34:49.795: //232046/8D...
Dear Team, I have configured a system call handler in the cisco unity connection, but as per the user requirement, after the greeting, if the user dials any extension which is configured on CUCM, it should transfer the calls to that extension. How ...
Hello, We are having a strange problem our Call Manager is ver 14 and we have a mixture of 7941 and 8811 phones. This has been this way for at least a year this week some of the 7941 phones began experiencing static , bad quality , r...
HelloI just set up an installation of 4 cisco ip phone with CME 9.12 ( 7911 Model )2 ( 6945 Model )All the 7911 ip phone was able to upload the firmware and works perfectlyThe two others 6945 Ip phone model upload the firmware SCCP6945.9-2-1-0 succes...
I am currently working with a vendor on integrating an Iridium 9575 Sat phone to our UC environment. Currently we have inbound calls from the Iridium Sat phone ring to a desk phone and works for two way conversation. The problem we are running int...
I have a line on an H.323 Gateway that I want to add 9 as a prefix.We are on CUCM System version: 12.5.1.13900-152Question 1:Can I add a 9 as a prefix to all outbound calls on a specific voice-port\dial-peer voice pots from the CLI?Question 2:Can I a...
I’m stuck...I inadvertently hit reset service mode and now my phone is stuck at asking for an activation code or service domain. This isn’t an issue of using it remotely and returning to the same location. It’s never changed locations. Service mode s...
Is there a better way to assign a user to multiple system distribution lists?My current workflow:- Open voicemail #1 distribution list, add user- Open voicemail #2 distribution list, add user- etc, etc....9 times for any new call center employees.See...
Hello CommunityI'm facing issue with switching between Route Groups which is prioritize in the Route List, I have 2 prioritized list of available paths (i.e. two PRI connection) in route list when the service outage occurs for the 1st path then the a...
have setup direct routing recently with CUBE .. My ITSP (in Australia) appears to accept alaw as 1st preference followed only by ulaw as 2nd choice before sending 180 ringing back ... What I noticed is if i call an external number from Jabber registe...
My organization recently upgraded our CUCM and CUC from 10.5 to 12.5. We have a mix of 7900 series phones (running on SCCP) and 7800/8800 series phones (running on SIP). Prior to the upgrade, DTMF worked on all phones. After the upgrade, DTMF tone...
Hi,is there a way to enable mobility for all users bulk other than using cucm , And second question for a remote destination profile for snr requires any type of license Thanks
Hoping someone can fill in a hole for me. I am attempting to setup autoenrollment of the user certificate for wireless access for a set of 8865s. I have used the Cisco IP Phone 8861 and 8865 Wireless LAN Deployment Guide to the best of my ability, ...
I have two CUCM Clusters, for this example I'll call them CUCM Cluster A and CUCM Cluster B. They are both on the same network (different vlans). Cluster A and B have their own CUCM Pub and CUCM Sub. Cluster A and B do connect via SIP Trunk for inter...
