Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a SIP trunk in India with TATA which I cannot get registered and the provider is of no help. The relevant config is here: sip-uacredentials number XXXXXXXXXXXXXX username XXXXXXXXXXXXXX password 7 YYYY realm SIP-XXXXXXXXXXXXXXauthentication u...
Cisco 1760:C1700 Software (C1700-SV8Y7-M), Version 12.3(4)XG1VIC Slot 2:Dual FXO Voice Interface CardHardware revision 1.1 Board revision P0Serial number 0030977039 Part number 800-02495-01"caller-id" command is not available on voice-port configurat...
Hello,I have 2 routers C8200 with CUBE license working as a redundancy pair (main/standby) to manage SIP calls.The routers are working fine but when one of them crashes then the router reloads automatically, i know that enabling no redundancy-reload ...
I use Webex Calling and integrate CSR 1000v(Azure) as Local Gateway Webex Calling > CSRv1000 > ITSP CSRv1000 / privacy ip-10.0.0.4 / public ip-20.59.121.X CSRv1000 Public IP：20.59.121.172 / CSRv1000 privacy IP：10.0.0.4ITSP IP：211.75.165.204 Webex Cal...
I set up a two FXO ports trunk group (old cisco 1760) with priority on first port.It works, but if I detach PSTN from first port (line failure) , the call is still routed via that port.Is it possible to make system aware of failure in order to use th...
Call Flow: Third Party SIP device registered to CUCM > CUBE for outbound call, below is the invite and then the 422 session timer too small. CUCM min-se value is set to default 1800, and looks like 2000 is expected. CUBE is set to 2000 under voice s...
hello, I have a cisco 8851 model phone, we want to include it in our exchange, but there is no interface, how can I access its interface, thanks
Dear All,I am configuring C8300 VG, i need a procedure to activate the licenses and we have SRST licenses deposited into our SA. How this licenses will be consumed?
Dear All,We have SRST endpoints licenses deposited on SA, When we configured the SRST configuration on Voice Gateway. The licenses are not getting update on SA. When we try to sync from router, getting an error communication failed. I need a help in ...
We have a product called SecureLogix that is inline to a few PRI lines that terminate to the CUBE router. It performs some basic call reporting and helps filter out spam calls. The version of SecuireLogix that we run is very old. We are planning to m...
Hello Experts,I have an issue that the outbound calls give one ring only and the voice gateway send a bye message with error " Cause=96 Mandatory IE missing error" we send the error to the SP , but they send that the GW is sending the bye message and...
This is a new setup with SIP, when we place outbound calls we receive a 408- "No user responding" error in debugsThe configuration is as follows*****Pattern Map****voice class e164-pattern-map 202description *** Patterns for calls to Vodafone ***e16...
Hi All,We are planning to upgrade our current CME 2900 series with a newer Cisco 8200 series. Additionally, we are also looking to replace our existing Cisco 8821 wireless phones with the newer Wireless Phone 840 and 860 models.I'm curious if the new...
Hi all, we have a CUBE that is choosing a new outbound dialpeer upon receiving a REFER. How can I get it to maintain its current connection? I've tried a few refer-related commands in the CUBE, hoping they would preserve the existing outbound connect...
Hi there, I am learning to work with the CUBE. At the moment, I have been able to make it to where outbound calls are working as expected. Incoming calls are not being routed to CUCM from CUBE. Instead, they are being sent back to the PSTN, creati...
