Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a few cisco cubes with different providers! Is there an easy way to calculate max outbound calls per second, per cube? I am struggling- CUIC/RTMT/CUCM/CLI? Any help or direction would be appreciated. Would like to do last 30 days or all hist...
Hi All,We have 40 no's of CP-6921 with firmware 8.5.1.66.22 which were not used since 2010. Now we are trying to use them and we are not able to upgrade the firmware to 9.3.1.2 as our CUCM version is 8.6.2a SU3. Can anyone kindly suggest whether ther...
Hi champs, i am trying the add the NIM-2MFT-T1/E1 card in the CUCM (12.5) and the CARD is installed in 4451X. I configured SIP Trunk between CUCM and VG4451. i can only add the FXO/FXS Card in the CUCM which is showing in the Module 0 is there any co...
Hey Everyone,i have a customer with 2 ucs220 server in sperate side that we installed for him with CUCM/CUP/CUC ( all version 12.5su4)in one of the side the servers shutdown because power problem in the building and after that all the servers in the ...
As we had issue to login to our Publisher, it said 'Data Communication Error', we restored Publisher which contains Cisco Prime License Manager from third party backup system, now our Cisco Prime License Manager says ' Registration Conflict'.Anyone k...
CME 12.0 // All 8851 phonesHaving a devil of a time here getting Call Park BLF's to work. I have two BLF speed dial line appearances setup system wide for two call park slots on 8851 phones. I can not seem to get the BLF's to illuminate at all wh...
Hi all, hope everyone is doing well !!Has anyone successfully register a Cisco ATA192 with a 3rd party session border controller or an IP PBX ?I have a few Cisco ATA192's that were once registered to my Cisco CUCM that I would like to reuse to regist...
Dear allI have CME ver 14.1 on ISR4331 with UCS-E160S-M3/K9 having CUE version 10.1 (10.201.47.7).Internal and PSTN FXO calls are working normally.SCCP phones (7945) cannot dial 444[567} which is Auto-Attendant dial-in number in addition cannot dial ...
We officially swapped over from REDCOM to CUCM on SIPR last night. All of our phones registered and function as intended except for one, a 8865NR cisco phone. The other phones that we have are 7942, 1945, and 7965s. The phone functions normally bu...
We have a multi-tunnel path in our network from Hub to spoke. We can ping from hub access switch to the spoke access switch. The spoke access switch can ping the CUCM and DHCP server. Before deploying the phone, VTC and workstations, I configured ...
Hi I have a number calling my DN and I want to block this number to call my DN only so is there any method to block one number to call one DN and can call others without creating partition , also is there any difference if this number inside or outsi...
We have an ISR/CUBE running and it has been in production for several years, but we it was reported that inbound/outbound calls were failing. In troubleshooting it appears the SIP service is disabled, and I believe it has something to do with Licens...
Hello- I'm switching my landline phone system over to RingCentral VoIP and ordered a new Cisco 8861 off Amazon. However, the provisioning through RingCentral's admin portal is failing and their tech support is telling me the device has some features...
Anyone know if it's possible to run RTMT Linux on a Mac, OSX version 5.5?TIA,Brian
Dear all,I took over administration of our VoIP phones since the old admin quit unexpectedly.. We have approx. 150 phones from Cisco - IP PHONE 303, registering on Asterisk phone gateway. I now need to urgently add new phone to our network - the Conf...
| User | Count |
|---|---|
| 7 | |
| 4 | |
| 2 | |
| 2 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
