Hi,
I have a customer who needs to replace a faulty AIM-CUE Integrated Service Module - part number: 800-20063-04.
Can you advise if this module is still available? If not, is there a replacement that will work in a 2801 router?
Many thanks, John.
Hi,
can someone please confirm the signaling in terms of isdn,sip and h323 what happens when you hear the music instead of ring back. is it the early media in sip?
detaling would be highly appreciated.
Thanks
Hi everyone,
I installed CUCM 11.5, and CUCME v7 on same LAN, I have 14 VG Router for Fax configured on CME, Now I want to configure VG Router in CUCM, is it possible to define two management IP addresses in the VG Router, the first of CME and the se...
Only happening with one user.
There is a user who is using 7821 phone.
Active Load ID:sip78xx.11-0-1-11
Call manager version :11.0.1.21900-11
When the user tries to fwd all to an extension, it works fine, but when he tries to cancel the fwd all, ...
I keep on receiving the alert from the Call manager (Publisher) which says CCMLinkActive has gone down to count 1 from 2.The alert clears after around 10 minutes. This has been happening for a few days, but I cant seem to find anything in RTMT about ...
We have some CP7841 phones that have having an error when trying to Use the forward all calls button. When the button is pressed it asks for the extension as normal but as soon as you hit a digit a error voice message says call cannot be completed as...
Hi,
we are working with Auto-Registration at the IP-Phones.
We have 1 PUB and 2 SUB in two different locations and also 2 CM-Groups / device pools for the two locations.
When we configure phones manually to device pool 1 then the phones registe...
Dear all
We are in the process of upgrading Cisco voip routers from 38XX to 44XX routers , we found one of the translation rule which works on 3825 doesn't seems be work with 4431 .
Translation rule voice translation-rule 2002 rule 1 /^7\(5490$\)...
All,
I have a situation whereby faxes are failing to a fax attached to an FXS port on a Cisco 2901. (H.323 with CUCM)
The gateway is setup as follows:
fax protocol t38 nse version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711alaw
Fax i...
Hi,I bought the CP-8831 Conference Phone to replace the CP-7937, that use the built-in mic only (No the wireless / wired mic)I'm using on the small conference room. As the CP-7937, the calling out sound is very clear and the receiver caller hear is g...
I am working on a Cisco IP Telephony requirement where they need internal calling between their Existing NEC SV7000 IP Telephony with proposed Cisco CUCM 11.x. any one have experience with NEC SV7000 SIP integration, does it support from NEC side. ap...
have a Cisco 2811 with a VIC2-4FXO card and one analog line provided by my telco. I am trying to get the caller id sent by the telco to show up on an ip phone that is registered to my Call manager version 7.1. The gateway is configured as H323 and ca...
Hi,
I changed the security mode to mixed mode on our CUCM to enable secure RTP to a meeting server.
Therefore I'm also generated a CSR for the CallManager certificate, signed it by a CA, uploaded this signed certificate and the CA root to the CUCM.
...
All,
I would like to know if CUCM support PLAR/Hotline support across cluster for FXS or SIP phones. I have CUCM release 11.X across cluster. What's major difference between PLAR and Hotline? I see that configuration is same except hotline use route ...
