Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear I am not getting phone registration to CME. CME version is 10.5. phone is 7942. I got the following messages like TFTP:file is locked SEPECC882B04055.cnf.xml and TFTP: Looking for CTLSEPECC882B04055.tlv What could be the reason. Below is th...
Hello all,I'm implemeting a CUCM 8.6.2 and under the Common Phone Profile Configuration there is a option (the last one) that is Background Image.According to the help file we have:Background Image: This parameter specifies the default wallpaper file...
Good day, I have a cisco phone with SIP firmware (SIP42.9-4-2SR2-2S), attached configuration file. But it does not connect to the PBX (Grandstream) server, nor does it generate output traffic to the IP address of the PBX server 10.1.14.2. With sniffe...
Hi, Running a couple CME+CUBE I noticed that the only traffic required to be permitted in ACL is SIP protocol – UDP:5060. Why on earth, a router permits RTP protocol without specific record in ACL?
Helloo All, i have configured power saving on my CME.so the phones turn off screen after working hours. once the screen is off if someone calls on the extension the phone rings and the red light on handset and button is also blinking but the screen r...
Hello everyone!! I'm working with few phones model 7861 and I need to configure one IP phone with two extensions. I noticed that the second line does not appear, even after making a call from it. i.e IP phone 7861- Line 1 - extension 6021- Line 2 - e...
The user is set up using ip communicator. While she is at the office, she can make calls and be heard normally but if she receives calls, she can hear the caller but the caller cannot hear her. This does not happen when she is connected by VPN from...
I am trying to add in UDPs via BAT and I can not get the UDP BAT Template nor the CSV file to add in 2 items under the Directory Number: Call Forward and Call Pickup Settings (for): Forward All - CSS Secondary Calling Search Space for Forward All I ...
Hello,Im trying to upload an wallpaper to DX650 but its not workingI use this procedure:Step 1 Assign wallpaper control to the administrator.Step 2 Upload the wallpaper to the Desktops/1600x1280x24 directory of the TFTP server, and restart the TFTP...
Hi, I have network diagramm: Phone (6348) - PBX Nortel -(E1)- Cisco VG -(SIP)- CUCM (7.1) - Phone (115xxxx). I can't make a call 115xxxx->6348. Cisco VG initiates - 500 Internal Server Error message.Please, have a look additional files in attachmen...
I am having problems getting calls across CUBE. AT&T calls are arriving to CUBE but CUBE is not sending the calls to CUCM. The same from CUCM getting to CUBE but CUBE not sending to AT&T. Ive been trying different configurations with the dial peers w...
Hi guys, I have two call managers (CUCM-1 Pub + CUCM-2 Sub) when I am regesetering my IP phones the phone take ip address of active server but not take for stand-by server! why? my CUCM ver. 11.0 What could be the problem here? thanks
Hi guys, Please any help for this problem. During installation CUCM subscriber I got this message during database installing ! The message is attached Thanks for all Mohammad
Dear All, I will really appreciate if anybody please help me! I am using cisco 2621xm with NM-HDV-2E1-60 module and I have connected 2 E1s from teleco. I can make calls successfully without any issue but I am facing one issue, when call is disconne...
Hi all, We need a help. We have CUCM and UCCX systems. When calling out we need to listen some message like < your call will be recorded>. Is there any means or capabilities to organize this kind of configuration??? Thanks
