Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, I'm stuck with locale problem on 7962G phones. There are several 7962G controlled by UCM 10.5.2 and one of them can not install Russian locale. In status messages i see "Error Updating Locale" message. The only difference between the same phon...
Hi, Im sooooo newbie. I want to change the codecs of the CUCM to use, by default G.729 or G.722. CUCM Version 10.5.2.13900-12 All phones in the company are Cisco 6921. Thanks :)
Hi, I have something weird, I configured a System Call Handler in Unity Connection and assign it an extension. In CUCM I create a CTI route point with the same extension and do a forward all to voice mail. When I dial the extension from the CTI route...
I am running cme 11.5 with 7841 SIP phones. A wireshark capture shows RTP streams going through the CME router and not directly between phones. Is this normal? Should I see RTP chatter between two SIP phones ? AT
Hello, The CUCME data sheet does not show support for the following item: Cisco IP Phone 8800 Key Expansion Module CP-BEKEM= Also the item's data sheet itself mentions CUCM and SRST, but does not mention CUCME specifically. Can someone confirm that...
Hi, I have CME version 10.5, and combination of SIP & SCCP phones. This is about remote presence using BLF speed dial. - SIP phone (8851) on site A can view SCCP ephone dn on the same site -> OK - The same SIP phone on site A can't view SCCP ephone ...
I am trying to make mutual call between two CMEs. When a SIP phone in one of CME makes call to SCCP phone in another CME, if the dialpeer between CME is H323, call is established but no voice (no rtp traffic is going). if the dialpeer between CME is ...
I have SNR/Remote Destination set up for several users and it works as expected. However, there are just a couple of users that are receiving "UNKNOWN" as the caller ID for all calls received via SNR to their cell phone. These users have the exact ...
Hello, in Communications Manager 9.x and above is there a way to compensate for 911 calls when a user is at a location other than where their DID resides WITHOUT having Cisco Emergency Responder deployed? Example. Jabber user resides in Office ...
I have 2 SIP dial rule PLARs on a 8851 SIP phone with side car bttn 6 and 7. When PLAR is used and a new call is attempted the PLAR is used. instead of the prime line to place the call. I enabled the "Always Use Prime LIne" on the device but this doe...
I have 2 SIP dial rule PLARs on a 8851 SIP phone with side car bttn 6 and 7. When PLAR is used when new call is attempted the PLAR is used. Client must select prime line to place call. I enabled the "Always Use Prime LIne" the device but this does no...
I use the SPA 122 which has the following specs: Version 1.4.1 (002) Model: SPA122, LAN, 2 FXS Product ID: SPA122 Hardware Version: 1.0.0 Firmware Version: 1.4.1 (002) Oct 26 2015 Problem: 1- The software gets corrupted again every few days! ...
Can we break up 256PVDM to 128 for conference,64 for Transcoder and 64 for MTP?? If yes than how??
So I have a CS530 headset with the APU-70 electronic hook switch cable. (this is the one with the USB connector) When I plug this into a 8961 with out a key expansion module, everything works as expected, but when I plug it into a phone with the exp...
Hi, I have 3 7911G Cisco phones that are unable to reset. I need to install «cmterm-7911_7906-sccp.9-1-1SR1» firmware. I use tftpd32 and this is my setting (I tried 3 differents versions of the utility and 2 differents procedures for this): https://...
