Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi There In my network lab, there are 8 routers (3925 and 3945) and 2 switcher (3550, 3750). This is a teaching lab in Concordia University. I want to make some test on Voip with Cisco IP softphone or IP communicator. But I don't know where to get a...
We have a CME ver 10.5 whose phones were half an hour off. Previously, we were an hour off because Chile's government likes to the change their DST times every year. I was trying to change the time zone manually, but the time-zone command in Telephon...
Hi folks, May be this is stupid question. Customer has VERINT as call recording solution. VERINT is configured with JTAPI user pointing to Publisher. In case, if Publisher goes down then CTI communication breaks and call recording stops. Is there a...
We have a two story building with 7821's upstairs and downstairs. When calls are made between floors, it sounds like you are talking under water. When calls are made to phones on the same floor the sound is good. Could it be the multicast? No errors ...
I am deploying a CUCM/CUC/IM&P system on spec based hardware. Is there a minimum number of UWL licenses that I need to buy or can I just buy one UWL Standard license to start with?
Hi,for some years i had the num2name script via ISDN up and working. No we change to SIP and i have the problem that it shows the name correct on the cisco phone but as soon as i pickup the phone the call is disconnected.See here the debug from VGW:R...
Hi I am looking at implementing Secure RTP between our CUBE and the ISTP. There are guides on how to do this which is great but would I also need to implement SRTP between the CUBE and the CUCM server? Basically is SRTP and end to end requirement fr...
Hallo teamOn CME 10.5 I configured a mixed mode shared line but I face an issue. When I try to call the number 160 only the SCCP Phone rings.I can make outbound calls from both SCCP and SIP PhoneSIP Firmware: sip78xx.10-1-1SR1-4Here is the config:voi...
Once the caller hears the following message after the recipient's greeting plays: "Record your message after the tone. When you are finished, hang up or press # for more options". Duration caller record message them can pass any key and get more op...
Phones are registered at CUCM. Asterisk is used for trunks. New branch is added with cisco 2811 (c2800nm-adventerprisek9-mz.151-4.M12a.bin) I guess problem is in Asterisk - CCM express communication. I try to make outbound call to 994125555555, call...
Hi Everyone. Can I ask your assistance on this because I am try to to upgrade/downgrade my SCCP Cisco 7965 from SCCP45.9-3-1SR3-1S. As per this bug CSCun26289 https://bst.cloudapps.cisco.com/bugsearch/bug/CSCun26289/?referring_site=bugquickviewclic...
Hi everyone! I trying register my CUBE (ISR 881) on SIP ITSP, but nothing happend. I tried use clear config (only public ip address on external interface and static default route) and its not help. Also I tried connect Service Provider cable to route...
Hi i would like to upgrade vg224 from version 12.4 to version 15.1. Any idea what file i should download and install on VG? Thx.
HI All Cisco 7961 phone is giving wrong time .. the setup is just upgraded fro CUCM 8.6 to 11.5 . after the upgrade only the issue started . we have around 10 phone of 7961 on site only 1 phone is having the issue . all the phones are running wit...
Dears I am working on CUCM 10.6. We are having an issue here, missed calls found in CUCM CDR analysis are way higher than the missed calls logs we found on IP phones for a shared extension. Do those missed call logs on IP phones retrieve missed call...
