Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Has anyone encountered the following: Intermittent delayed call audio on internal calls only (RTP setup is from device to device). We have two locations out of many other locations that are reporting issue (all with identical Meraki configuration te...
Hi Guys, My Customer have the solution with CUCM 105.2 with 05 sites. There are calls that not are completed and We received the error message: "1459617833 CCM_SIP_503_SERVICE_UNAVAILABLE". I reaserched in Cisco site and another sites the signficat...
HelloI am experiencing some strange issue with my VOIP in 1 of my branches. our branches are connected thru IP VPN and 1 of our branches are able to call our office in HQ (ringing but no voice) other branches are able to call our office without any ...
Hello,This issue just started happening with one user. when he Call from his extension to any other extension the call initiate after 10 to 12 seconds. Thank you,
Hello ,I'm looking for to download the french locale for the CP-6941 phone.I'm using freepbx and need the user locale and the network locale .I checked cisco's download site and found only the firmware ...Tyvm for your insights
I am using CUCM, and I already have caller ID that displays the external caller’s number. One of my users wants to see the caller's name for external calls instead of the number, but only for two specific numbers. The others should remain unchanged. ...
Can you use a Clarity HA40 phone amplifier with a Cisco CP78413PCC landline business phone for someone that is hearing impaired in order to hear clearly on the phone? Thanks, Karis Seiber
Folks,I am new to forum participation so please be aptient and kind.We have CUCM 14.0 and I have an important business that would really like calls from a particular external caller to ring in distinctly. They already recevie calls on a specific lin...
HiI have enabled extension mobility.I understand that the service is configured properly as some users are able to login/logout successfully and when I check the URL in the settings of their IP Phones it displays the IP address of the server.For some...
Dear Community,I have the following topology and I wanted to know if anyone has done a similar configuration and could you send me an example.I have a Catalyst 8200L are licensed by SRTS and UCME. This switch is Ethernet only.Then there's a VOIP Gate...
Hi, I'm having problems to redirect incoming call from sip trunk to CUE AA,- I have a Cisco 3945 and a NME-CUE , VID: V04- the sip trunk provider only gives the last four digits.- sip trunk number 8800 redirects to extension 100. Works fine.- sip t...
Hi,I am currently using a Cisco Phone CP-7962G with software version SIP42.9-4-2SR3-1S. I want to configure two SIP servers to enable redundancy. In my setup, the primary server is 192.168.191.72:5080, and the backup server is 192.168.191.73:5080. My...
Hello! Is it possible to provide this inbound call scenario: when somebody calling to hunt pilot number with four members it calls in broadcast for all of them and after 6 sec. of noanswer is forwarding to external mobile number but all of them con...
In our office in Zurich we like to block an specific outgoing number.We have created several route paterns what will block/reject this specific number.But we like to do this on the router instead of the CUCM.Has someone a suggestion?Thanks in advance
I am able to ssh to the 8851 just find and do a 'test key soft1' command just find.But not able to the the advanced commands like 'test key set' or serv.Is there something I am missing?Is there something in CUCM that I need to enable to do these comm...
| User | Count |
|---|---|
| 6 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
