Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi All, We are getting bulk error agents login issue. We have contact center setup and we are using WEBCRM for user login with phone extension. Please provide me solutions and resolutions. Error Details: Someone is already logged in.
Hi dear, i have a translation pattern for meet me number cannot dial from mobile phone or PSTN. please help Thanks
by default in CUCM Full consult transfer. how to switch to Blind transfer? Is it possible to a set of selected numbers ? partition to another? is it possible to programm a key 7821 to Blind transfer to a fixed number?
Hello Everyone! I am confused on a seemingly harmless error/warning I am getting on a router (ISR 4351) iOS XE 03.16.00.S.155-3.S-ext.SPA On incoming calls a "debug ccsip all" shows this: Apr 25 12:34:22.494: //214953/C83C664091E7/SIP/Media/sipSPI_i...
Hi all!I'm looking for phones that support SPANless call recording. Does anyone know whether the phones 7821 has built in bridge or not ?Thanks!
Hi All Do the VIC3-E/M ports use the same pinouts as the VIC2-E/M and VIC-E/M? Cisco provides the pinouts for the VIC2-E/M and VIC-E/M via this page and states that RJ48S is used: http://www.cisco.com/c/en/us/support/docs/voice/analog-signaling-e-m-...
Hi, We always get a busy dial tone when dail a specific number(external) otherwise there is no issue in making external calls. I have also dialed that number from mobile and landline that's working fine. Can someone help? We are using Call manager ...
Note: These are all internal calls. Nothing hitting the PSTN. I am having a problem where my 6900 (6921 specifically) series phones are getting a weird problem when calling into a CCX line. When the user calls they hear the greeting and then the ...
Dear forum users. I have a VG350 Version 15.3(3)M2. According to the Cisco Feature Navigator (see attached pictures), , this supports Ether-Channel for both “Link Aggregation Control Protocol (LACP) (802.3ad) for Gigabit Interfaces” and “EtherChannel...
Hello,We have a deployment for Collaboration Edge where customer want to enable SSO. That's fine for Jabber. Customer has 7800/8800 IP phones, DX series and the SX series that are being used today as MRA devices, will they work ok?Is there a signalin...
Hello, We are currently upgrading to Asterisk 13.6.0 from Asterisk 1.4.44. I would like to know if Cisco 7960 and 7961 phones are compatible with Asterisk version 13.6.0
Hello I have some ip desk phone 7940 ( i know it out of support or end of live) for my customer my problem is to convert in sip protocol to connect with 3cx phone system i try all the tftps serveres and firmware but it not work if i try wrong pleas...
I'm trying to understand this translation-profile that I have setup on my Voice Gateway router. I didn't set up this rule. It was setup by a person who worked before me. It looks like the intention is to block toll fraud. Can someone explain this...
Dear All, Since I am running shortage of DLUs and I can see that CIPC could be configured as an adjunct device and consumes fewer licenses, so that it saves me a couple of units, may I know how do I do that? Thank you in advance
I have a Cisco 2901 ISR running CUCME with the VIC-4FXS/DID for fax machine. Calls are coming in via T1 PRI. What configurations are needed to add a fax machine in one of the FXS port and get it working? I already have all the phones in the system wo...
| User | Count |
|---|---|
| 6 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
