Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I am using Cisco 2901 router (CME) with Cisco 7841 SIP Phones. These phone should be able to make conference calls. I think three users can conference with each other by default because I haven't done any configuration and it still works. But the pro...
Hi, I am trying to register a CISCO 8831 conference station with CME running on ios 15.3 and the phone firmware is sip8831.9-3-3-5.loads but the phone is not getting registered. Can you please let me know if there is any compatibility issue of the f...
Hello. We have one C220 server and installed Vmware 5.0. Than we have installed one CUCM (pubilsher) as VM on Vmware and added liecnses to ELM. CUCM and ELM are co-located. CUCM worked normally during a year. But after power cycle the server VMware...
In CDr file we can't see the calling party number its shows null under the calling party number field. But in ip phone its appearing a calling party number.The call flow is like this.PSTN>H323Gateway>FXO>PLAR NUMBER>IP Phone.The cisco call manager v...
I would like some help trying to figure this out properly We have multiple sites so for instance Site A and B and both have gateways and both at different geographical locations we have certain numbers which are local to site B so they would be diale...
Hi!! I have a customer that want the users to dial 112 and this must be converted into na internal extension 888 and not goint to the outside. Using translation I dont have the option, or I dont know, to remove de three digits 112 and replace them w...
With the release of the newer series of handsets (7800, 8800) it seems like Cisco is transitioning to SIP only endpoints. For phones that support video on board it makes sense, are there other advantages to using SIP over SCCP? Are there any features...
hi,i tried configuration cisco router 2811 (ucme 7.1) with x-lite,configuration is :int fa0/0 ip address 192.168.1.1 255.255.255.0 no shut-->exitvoice service voip allow-connections sip to sip sip registrar server expires max 1200 min 300...
We are having problems codec with the following scenario: When making a call from the first CUCM to a phone registered with the NEC PBX ring but we have to answer the call is dropped. This happens bidirectionally. (currently under implementation) P...
Hi Everyone, I have an office reception that consists of a Hunt Pilot that diverts to 2 telephones. They have complained that when a call comes into the hunt group there is an audible beep which they find interupting. I believe they mean if on a cal...
Friends, One of our customer requested for CUBE licenses for 3800 voice gateways. I have checked in the CCW and unable to find out the part number. The part numbers for 2900/3900 are available. Kindly let me know how I can order these Regards Rathe...
I have 2 clusters site A runinng cucm 9 site b runing cucm 10.5 i need to shutdown site A and transfer all license to site B I need a document how to do that
Hi everybody, CUCM is using QSIG to connect with Siemens via VG Call flow : Cisco IP phone --- CUCM --- VG --- Siemens PABX --- Siemens Phone When "Cisco User A" 171 calls to "Siemens Phone X" (700), it does not show the caller ID "Siemens Phone X...
Hi Everybody, Currently I have a problem on CUCM bulk admin phone export CUCM version is 10.5.1.10000-7 When trying to use Bulk Administration > Phones > Generate Phone ReportThe job scheduler shows the job result is EMPTY. (Selection Criteria devi...
Hello Everyone, We have new Cisco IP Phones 8845. However, device is not yet included in the options when adding a new phone. They said that we need to install the whole device package. When choosing phone type, other 88XX series are already include...
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 2 | |
| 2 | |
| 2 |
.jpg "VIP Expert"){kind=icon}
