IP Telephony and Phones

How to enable call logging history on Cisco CUCME?

We are a small (<100 person) company running CUCME 8.6. Is there a simple way to enable call logging history without having to collect the logs off-box? I am looking for a way to simply keep a log of the past 200-300 calls (we don't do that much ...

Resolved! how to add dobly conference phone (vcp9000) to cucm 9.1

Following Dolby's instructions, the phone registers with CUCM and can receive external calls. The problem is it can't make calls...internal or external. When trying to make an external call, I get a busy signal. Calling an internal extension will r...

IP phone 78xx firmware downgrade from sip78xx.10-3-1-12 to sip78xx.10-2-1-12 as workaround for Expressway

Hello peopleRecently we updated firmware for phones 78xx (7821 , 7841 , 7861) in CUCM (System version: 8.5.1.10000-26) from firmware version "sip78xx.10-1-1-9" to "sip78xx.10-3-1-12" this as a workaround of problem phones won´t register in CUCM.Now s...

Resolved! Cisco Bug: CSCul18667

HI AllWe have been facing an issue in our cluster where UCCX cluster has failed over from uccx-1 to uccx-2 as the master . and after some troubleshooting we found that Cisco Bug: CSCul18667 is causing the issue.Now, Cisco Bug: CSCul18667 - CUIC doesn...

Resolved! UC500 and 3905 phones

Hi All,Could we register a 3905 as a 3rd party SIP phone on a UC540?Thanks in advance,Nick

BE7000M --CUCM 11.X deployment-related issues

There are two BE7000M servers, install CUCM11.x, how do I configure both hardware and support 7500 users, the Redundancy model that you choose, in addition to this problem, I still have doubts, the document describes BE7000M supports up to 5000 users...

CDR missing select phone call records

I have a 10.5 CUCM cluster . I see that some of completed calls from Mobile phones to internal numbers do not seem to appear in the CDR records at all. But on the other hand I made similar calls to other internal extensions which seemed to be seen i...

7911 Phone with SG300 switch are not registering to CUCM

Dears, I have 7911 ip phone which are not registering to CUCM once I connected it to SG300 switch when I connect the phone to 2960 switch the phone register normally and works fine. I already tested another phones like 7975 and 7841 with SG300 sw...

DX650 dialing delay and same extension display different names on IP Phone and Jabber

Dear All, I have 2 questions. 1) Customer has cluster over wan setup and many branches are connected by WAN router and Voice Gateways. When dial from any IP Phone like 79XX series call goes fine without delay. But when dial from DX650 there is delay...

Call waiting on analog and IP Phones

I have 1 UWL license for 2 devices; 1 IP phone and 1 analog (ATA190) same phone number on each phone. I would like to have call waiting set up on both phones so if a second call comes in I can answer it on either phone. Is this possible? If call 1...

NEC SV 8500 SIP Connection with Cisco

Hi We are doing SIP trunk integration between Cisco call manager and NEC SV 8500. From NEC we are able to call Cisco user but one way speech ( Cisco user can hear NEC voice) but from Cisco we are not able to call NEC. Can anyone help me on this ...

Resolved! Call Forwarding for VOIP & PSTN

Hi, We are running CUCM 8.6 with Single line ( VOIP & PSTN) with Geo location & LRG in place. Also we have UNx 10.5. Current Requirement is 100 users are moving to different location in same cluster. From Location A to Location B. Requirement: Us...

Resolved! no ringback tone

dear sir, am not getting ringback tone on fxo and fxs ports why?

Cisco DX650 trying to dial SIP URI instead of extension for intercluser user

Cisco DX650 trying to dial SIP URI instead of extension for intercluser user. DX650 registered to CUCM 9.1.2 in sydney cluster with all users (US + Sydney). Call a US user from directory, tries to call as first.last@<IP of Sydney Sub> instead of ex...

CUCM 11 User Device Profile Template - BAT

With previous verions of CUCM you were able to assign a Line Template to the User Device Profile Template within BAT - i'm currently deploying CUCM 11 and this option is no longer available, it only allows you to add a Directory Number to the UDP Pro...

IP Telephony and Phones

Forum Posts

How to enable call logging history on Cisco CUCME?

Resolved! how to add dobly conference phone (vcp9000) to cucm 9.1

IP phone 78xx firmware downgrade from sip78xx.10-3-1-12 to sip78xx.10-2-1-12 as workaround for Expressway

Resolved! Cisco Bug: CSCul18667

Resolved! UC500 and 3905 phones

BE7000M --CUCM 11.X deployment-related issues

CDR missing select phone call records

7911 Phone with SG300 switch are not registering to CUCM

DX650 dialing delay and same extension display different names on IP Phone and Jabber

Call waiting on analog and IP Phones

NEC SV 8500 SIP Connection with Cisco

Resolved! Call Forwarding for VOIP & PSTN

Resolved! no ringback tone

Cisco DX650 trying to dial SIP URI instead of extension for intercluser user

CUCM 11 User Device Profile Template - BAT

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

Cisco 7942G Firmware

%VOICE_IEC-3-GW: C SCRIPTS: Internal Error (Digit collect failed): IEC

CUBE proxy with Dual Recorders SIP invite error 500

How to add personal greeting in cisco unity ?

Incoming calls show as forwarded

Cisco Jabber

IMAGICAL BILLY BLUS

CUCM CAP-RTP-001 and CAP-RTP-002

Issue with ciscocm.enable-sha512sum-2021-signing-key-v1.0.cop.sgn inst

How to setup SAML SSO authentication in Expressway C