Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
RTMT is porting the following from my Publisher and both Subscribers. At Wed May 28 15:10:11 BST 2014 on node 10.211.7.100; the following SyslogSeverityMatchFound events generated: SeverityMatch : Critical MatchedEvent : May 28 15:10:04 dbs-cm-donpu...
Hi Guys,In our environment, we have CUCM 8.5 with LDAP sync and newly we bought 5 Cisco ATA 190 Phone adapters. As this cucm version does not have the firmware, so we have download the firmware for this device and uploaded it. Also we created the end...
Dears, Its possible to lock the IP Phones, no one can access my IP Phone and call from IP Phone. We are using CME.
I am currently having a problem where DTMF relay is not working correctly from a new SIP ITSP. My topology is ISTP<-->CUBE<-->CUCM. I was not involved in the inital planning session with the carrier however I am of course assuming that they are suppo...
Symptom: cannot transfer calls from 7941 and 7942 we recently loaded the cmterm-devicepack9.1.2.12039-1.cop on our Call Manager version: 9.1.2.10000-28 for DX80 support. older model 7941 and 7942 model telephones are subject to the bug listed below...
Hello, According to Cisco Feature NAvigator tool, seems the MTP feature (included in the Feature category named "DSP Media Services: Transcoding, Conferencing, MTP, TRP") is available only for XE versions running on hardware platforms ISR 4400, 4...
hi All, Internally I have 4 digit extensions in 7xxx, 2xxx E1 public number DID subscribed from telco = 3227000 to 3227199 MGCP voice gateway Objective as below Outgoing call Eg: All extensions starting with 2xxx eg, Ext 2323 makes outgoing call, c...
We have a set up wherein we have our internal network consisting of IP phones registered on CUCM and we have PSTN gateways for c onnecting to the outside world.I need a solution wherein I can force disconnect any outgoing call to the PSTN gateway aft...
Hi , Good Day. We have 800 IP phones and we are planning to change the extension number of all those 800 IP phone. Can CUCM support this bulk configurations. Current version of CUCM is 8.5 I tried to export all phone details of a 7942 phone then do...
Hi, Several times it happens. I configured the controller T1 interface as the below, whose timeslot is 1-8, but after some times it became timeslot 1-24 automatically. Then "show ip interface bri" shows there are 24 interface. Anyone have this experi...
Hi, Occasionally, the isdn does not function well in my voip environment. That means that when show isdn status, the output is not as below State = MULTIPLE_FRAME_ESTABLISHED In order to solve the issue, I set up isdn connection between two routers w...
Trying to move configuration from v8.0.3 to v9.1.2. I have tried using a header.txt file from the v.8 cluster and from the v.9 cluster with the same message. This error is from the header file. The validation passes the config file (css details in th...
Experts, I have CCUM 8.X and Cisco Unity. I am wonder how I can move / copy all voice mails of one particular user. After that assign that voicemail to another user / extension. Sounds a bit of complicated but just wonder if there is any way to ach...
Hello all! I am working on adding 7800 series phones to CME, version 10.5 and am running into some issues that I can't seem to find answers for. Issue #1: I can't seem to put a call on Hold on the 7841 (SIP) that I am testing with and use Pickup on ...
Hello Friends, We are having issue in call forwarding option in Cucm. when we try to forward any call on external DN, call is being answered but both party can not hear each other. 1. internal forwarding is ok only problem with external forwarding. ...
