Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, everyone. I have some problem with Cisco ATA Fax. I can't sending and recieve fax. Toplogy: FAX (Xerox ApeosPort IV 3070) -------- ATA 186 ----------- CUCM ------------ CUBE ----------- PSTN Fax : Support G3 Please check my configuration
I am in the middle of upgrade - CUCM 7 to 10.6. For the last 8 years users have an User Device Profile (desk sharing) extension for their IPCC extension, additionally they also have a soft phone (CIPC) so they can also work from home. Apparently ...
hi there, need a bit help on this one.We have existing CUEAC running, the call flow details as following:incoming call to main number 9988 6200, transfer to 4 digits --> 6200 ( on router via translation-profile)on CUCM 6200 (translation-pattern) --> ...
Dear FriendsI have installed CUCM version 10.5. We have near about 300 IP phones. In some of IP phones directory is not working properly which was working earlier version. I am facing this issue after upgraded to new version 10.5. I couldn't see miss...
Hello, I am having some issues when registering a few gateways to a call manager group. I have three UCM's in a cluster of pub, sub1, and sub2. I have created two goups since we have two locations. Group 1 is Sub1, Sub2, Pub. Group 2 is Sub2,Sub...
I am trying to call number shwed below from my CUCM v.10.5 and I am receiving "Precedence Level Exceeded" message. Phone from which I make a call is in CSS which is allowed to make international calls. I believe that this is due to Route Filter appli...
Hello,When we use a sniffer in order to check the traffic in the network, we observe that there is IPv6 traffic generated by Cisco IP Phones.We need to disabled this kind of traffic because of the requirements of the client. I already disabled IPv6 f...
Would like to get help for configuring external URI dialing. We had implemented IM Presence 10.5 , cucm 10.5 & expressway c & e & we had CUBE routers. I heard we can setup sip route pattern for URI dialing. Did anyone tried this or give me idea how i...
Hello, I have an issue with ATA 190 is not giving any dail tone .I am able to get incoming line ringing but No out going . Can anyone help us on this please ? Regards Srini
Hi All, We installed the Cisco Prime Collaboration Assurance 10.6 . We got the below error while access from the firefox. "Error code: ssl_error_weak_server_ephemeral_dh_key". We have done the workaround as mentioned in supportive documents. But we...
Hi All, We have planned to upgrade CUOM 9.0 to Prime Collaboration 10.6 Advanced. please clarify below doubts. 1)As per the upgrade guide , we should upgrade to 10.6 from either 10.0 or 10.5. 2) If we are going to follow this 2 stage procedure,befo...
Hello All, I am facing with wierd issue with no answer timeout in CUCM 9.1.2. In service parameters is change default value to of this timer to 30 seconds. Same value I set up under DN configuration but for all phone which are under one specific Dev...
Hello, I need help to implement the qos on such equipment. should we apply this qos on all interfaces and also the vlan. could you please guide me see diagram thanks
Hello Friends, I happen to view a log file where I am not seeing a MOH server being used when put on hold. Two phones registered to the same call CUCM. One is SIP and the other is SCCP. I tried calling the other with local 4 digit extension and p...
Hi All. I'm a newbie on UC and I would like to have some advices from experts here. We are implementing a Voice Gateway in our client site, Japan office. The CUCM(ver. 10.5) is located in another country in EU. Our client want us to configure SRST mo...
