Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi All, I hope you all are doing good, I have few Queries concern to IP phone 1) How IP phone understand the contact DHCP for IP address? If We have 3 DHCP server confirued in our Network, How IP phone will contact DHCP and which DHCP server for ...
Hey guys, I have a Cisco 8865 phone that seems to be having a strange issue. We have used the official instructions in the manual to try and clear out the recent call list using the Application/gear button. We have also used the 2nd from top right ...
Hi all,We have 2921 router supporting DHCP pool.I have created ip dhcp pool voiceneed to know what does command option 150 ip x.x.x.x will do under ip dhcp pool voice?we are using cisco phones?ThanksMahesh
Hi Experts,Recently one of our clients has a working CCM 4.3 and is using 7911 IP Phones both at HO and remote sites. All is working and fine, until we change the server with a new CUCM 7.0, all IP Phones at HO registered as expected and working, bu...
Hi everyone, One of my clients was involved in a toll fraud hack through their Unity Connection server (from what it seems like...)All the calls originated from the Unity Connection voicemail ports in CUCM when I look at the CDR records. I checked th...
Dear All, we have Cisco IP telephony system with 2 Call Manager (UCS C200 M2) with around 1200 cisco IP Phones. suddenly Pub gives HD error Indicator (yellow Led) after 10 days same issue happened in SUB.. I need support how i can fix this issue.. ...
I am trying to setup a 3945 as a SIP to SIP gateway for lync. I am not able to dial out or in. I can see the incoming calls getting to LYNC and it attempting to process it, but I only get one way RTP. One number, it looks like the call goes to th...
Hello, 1. there was requirement from one of our client...they purchased DID range of 50 number...that is 1 E1 PRI with 50 DID range 4241 2400-2449..numbers of users on site are approx 90..we generally configure user extn of 4 digit of last 4 digit of...
Hi, I have doubt in globalized call routing for emergency numbers (With LRG in place). In the attached snapshot we are considering 888 as the corporate Emergency number. User who dials there respective emergency number (911 or 112) gets translated (...
Dear All, I am having problem on my branch office with hold/resume. Here is my call flow; Cell Phone -> Analog Line -> FXO Port -> VG -> H.323 -> CUCM When an external phone user calls my branch office over Analog line, it goes to DN on CUCM succe...
Hi, Is it possible to have visual alert for call pickup when using CME and SIP phones? I am able to pickup the line, but I have no notification about the call. Thanks! Regards, Dragan
Hello, We have a cisco 7937 confernece station. The display of the phone is always lit. Is there a way to just switch off the light of the display when the phone is idle and whenever someone wants to make a call and he touches any of the phone butt...
Hi Everybody, I'm going to create a meetme video conference. However, when config it to use VGA, only audio conference is allowed Here is the hardware: PVDM3-32 x 2VIC2-2FXOVIC3-2FXS/DID9971 ip phone x 3 Here is the VG config (working), VG(Confi...
Hi,Check out this new article about integrating Cisco Unified Communications Manager 9.1 with Cisco unity Connection 9.1.There is Cisco Unity Connection integration with Microsoft Active Directory as well. https://edsonvuma.wordpress.com/2015/12/17/i...
Hi, I recently set up a basic Netgear router to have WiFi capability in our building. The internet connection that I am using for the router comes from a port in the wall that previously a Cisco 7941 Series IP phone was plugged into. I was assuming...
