Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a 2811 running CME 4.0(1) (yes I know it's old) with a AIM-CUE module running 3.2.3 (the reason for the ancient CME.After much mucking about I have managed to get the CME to forward unanswered calls to the CUE, which is responding with the cor...
Hi, What is the availability of installing CUCM on UCS-E for small scale ?I didn't find it on Cisco Also is it supported to install CUCM 7 direct on UCS without VMware. I think not supported that Cisco states only MCS as supported servers but I need...
Hi All,Have a 4510 switch that I found 2 ints not configured in our standard format like most all of the other ints on the switch.When I tried to configure them with our standard config got the error message below after the "auto qos voip cisco-phone...
Hi, I have (1) extension when I called, after ringing and no answer it goes to welcome message (Auto-Attendant) and not going to voicemail box. I configured VM profile and Forward No Answer for this phone and the same configuration for all phones.
Hello All, I have users reporting an issue whereby when they dial into a conference bridge from there Cisco IP 7945 Phones, the call connects fine but when they enter the passcode to join the bridge, the numbers on the keypad which they are pressing ...
When a person calls on a cell phone, the visual call pickup notification says "Wireless Caller > Calling_name" Is there a way to display the calling party number instead of just "wireless caller"? I feel like this should be simple, but I google hasn'...
Somebody can say me why the Called# column is blank when I'm using the IOS command "show voice call status" ?For exemple :#sh voice call status CallID CID ccVdb Port Slot/DSP:Ch Called # Codec MLPP Dial-peers0x29C6 26...
Hello, Is it possible to setup SSO over collaboration edge with CUCM 9.1.2? Thank you, Sergey
I have a user that keeps getting an MWI on their personal extension. I think MWI is flagged in another mailbox for that extension. Is there a report to tell me if that extension is flagged for MWI in another mailbox?
Hello, I have CDR with my cucm 10.5, the issue is I have 2 E1 and I would like to know how I can configure the CDR to give me the report to what E1 is the calling connected. Thanks.
Hi all,kindly i need your help with a case i have, I have a CUBE interfacing a sip provider and this cube is linked to my Call Manager through a MPLS connection , When i make an outbound call it goes out normally with no issues but when i receive an...
Hello colleagues,Could you please help me to solve one task. I'm terminating sip trunk from sip provider on Cisco 2811 CME:dial-peer voice 2 voip description IN voice-class sip dtmf-relay force rtp-nte session protocol sipv2 session target sip-server...
Hi All,Is it possible for CUCM to identify a cell number associated with a user and then redirects the call to his IP Phone extension first, incase user is not available on his desk then the call will be routed out through PRI to Cell Phone number. W...
I have two ATA 186's registered to a Callmanager V7.1. We are located in the UK. When I plug a modem into the ATA, I get dial tone, the device dials, . and the modem handshake begins. The handshake caries on for some time until the other side han...
Hi,CME creates dial-peers for SIP phones:HUB#sh dial-peer voice summary 40001 voip up up 140$ 0 syst ipv4:192.168.120.22:40002 voip up up 180$ 0 syst ipv4:192.168.120.21: Is it possible t...
