Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, guys.I have CUCME, cisco phones and 3rd party sip phones (such as Escene, Fanvil, Grandstream). For cisco phones pickup is configured. But how to confgure pickup for 3rd party SIP phones?
Hello - we are looking at adding a SIP Gateway at one of our branches with SRST. The phones will be using SCCP for their protocol. Are there some good documents I could reference as a template for this configuration? Obviously this has to be built...
Dear All, I have cisco voice router 2811. I need to install and configure AIM-CUE module for it.Please guide me what steps I should flow to bring CUE in up and running state and to be accessible through GUI.I will be very thankful for your support.Re...
Hi Experts, I have 8941 model with Camera and I can't make a second call, I tried to change the maximum number of calls, but I couldn't change it's 3 just by default,Is there any way to solve this issue? Thanks Mohammad Saeed
Hi Expert, In my project I have guest room in hotel, and I have in this room Three Cisco IP phones and I need when some one call from outside, I will be able to hear the calling in three phones, if the guest want to switch from one phone to another t...
We have a SIP trunk setup to MTS Allstream in Canada. Outbound calls will fail /w a fast busy unless an inbound call is made to a DID. After the first inbound call is made outbound calling will work for a while and then go back to fast busy. It seems...
Hi, I would like to verify that IM&Presence server is not required for MRA Deployment.? Currenlty we are running jabber in phone mode with CUCM Only, we are going to extended it over the internet hence MRA.
Hello everyone;I do have an analog line that i want to affect to (04) four IP Phones, so that any one of these four ip phones users can use this same analog line, and when we call that analog line number, any one of these four ip phone users can answ...
Hi!.I would like your help. I´m trying to setup a configuration between 2 PBX one is CUCM 8.2 and the other is NBX. Here´s the deal, in CUCM I have phone numbers from 4000 to 4949 and in the PBX I have numbers from 3000 to 3999 and 4950 to 4999. So I...
Dears,During post installtion i gave admin username and password for AXL user, now I want to change a AXL username in CUP, when i try to change through the Systems>CUCM Publisher It gives me the error "Error: [4092] Failed to verify if the CUCM and I...
Hi Techies,Need a help in adding CP 8851 and 8831(conference phone) with CME running IOS version 15.3 (3)M3Currently I have phones 7945 and 7925 configured in CME using CM-Full-9.1 package files, but searched for 8851&31 phones in latest package file...
Hello There ,We have using cisco UCM 8.5,is there is any possibility to change the busy tone in call manager .instead of busy tone can we upload any voice prompts.please suggest the same. Thanks In Advance
I have a number of MCS-7825-H3 servers I need to clear the bios on. They have a BIOS password set and although I know the password current password I need to clear it. I have been told the only way to clear the password is to clear the BIOS via the d...
Dear All, I'm going to implement SRST for remote site on 2921 router.Need to help on separate PVDM3-32 installationSRST license installation (FL-CME-SRST-25)I hope configuration on router side should be -call-manager-fallbackip source-address X.X.X.X...
Hello,I have 8 QTY 7941G phone and i want to convert it to SIP as its currently running SCCP...Current setup is just an PC + POE Switch and 7941G phones. Is there any way i can convert this phones to sip ..??Pls help :(BRAkarsh.
| User | Count |
|---|---|
| 14 | |
| 9 | |
| 7 | |
| 4 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
