Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi Guys, I have built a CUCM v9 Cluster and I will license this via the NFR bundle so no problem. However I need to built another CUCM but this time it need to be SME,v9 I take it this is the same software it is just a different license. So my quest...
Hi,Is there anyway to re-run a migrate task only for subscriber after successfully migrate pub and if error occurs during sub migration? Thanks,
Hi all, I need to open ports in vpn connection for CIPC ,RTMT , historical reporting, and Jabber . Anyone knows which port I need to open ?
Hi Team, CTI ports are register with the CUCM ip instead of UCCX . There should be UCCX IP , Whts wrong ? Regards,
We are currently running CallManager version 7.02 with the following configurations: One Publisher and two SubscribersCM Groups - 2 Sub1-CMG (used by 9000 devices) Sub1 Sub2 Pub Sub2-CMG (used by 4475 devices) Sub2 Sub1 PubMaximum...
Hi, I am using cisco ip hones 7911 and 7962 registered in CUCM 7.1.5. When i hang up the phone call should disconnect/cut. But its not happening.
Hi,We have CUEAC 8.6 (physical server) and we'd like upgrade to 9.1 (virtual machine).I have checked the upgrade process (http://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/cucmac/arc/CUACEE_91110WAG.pdf) but the process describe the upgrade on t...
Asked this in the Support Communities but thought I would hit here too.Have a QS C20 that has been upgraded to TC 7.3.I am trying to manage the mic levels as I can on a C40 or SX20. When I go into the System configuration >> Audio, I am not seeing...
Hi All,We have a location where there is requirement of 6 digital phones and 3 analog phones. Currently in router they have a data T1.For digital phone I am planning to go with trunk line from service provider, connect to FXO card, configure plar con...
Hello!I need to configure any Annex, for example 3301-named line "Pedro Perez" and to call another annex the receiver of the call in the display indicate the name "Helpdesk", hiding so the ID of the line (Annex 3301) and only the name of the line ap...
Just got asked to pass the basics over to the Service Desk... as I described, provisioning a phone, a DN, attaching a user, with a vm mailbox. Sure, I can give them permissions to Manager... but I thought I'd read about a provisioning tool that was d...
We recently upgraded a system from 6.X to 10.X, there is a Speed Dial URL service that points to an xml file. The IP address of the webserver needed to be updated.The Service name is Speed Dial and it displayed twice on the phone, even though the ph...
Hi All, Please i need your help, I have a cisco 2921 with FXO ports that i will replace with the E1 Card (VWIC2-2MFT T1E1) which i have more PSTN numbers. I dont know how to configure it. After intallling tha Card i will also need to redirect call fr...
Hi,In an error log under C:\Cisco\CVP\VXMLServer\logs\GlobalErrorLogger dir I am getting any of these errors:-------------------the asctual ip address was changed to: 000.00.0.0001/14/2015 13:33:56.612, SERVER ERROR: bad_url. URI: /CVP/Server?audium_...
I have just connected a 2nd wic card in our 2821 for an additional 5 isdn 30 channels. I have gone through the config in the router and I am trying to work out the commands required to use the additional lines.
| User | Count |
|---|---|
| 6 | |
| 6 | |
| 5 | |
| 4 | |
| 3 |
.jpg "VIP Expert"){kind=icon}
