Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I've got a very vexing issue. I converted a router over from MGCP to h.323. IOS Advanced IP Services 152.4M6 With MGCP to H323there was never an issue :1. Intermittent call drop outs2. Inbound calls call hang up / call termination / en...
e have a customer with cucm 8.6. they are purchasing device license LIC-CM-DL for the additional ip phones.I want to know if its possible start selling UCL lics?Thanks.
If i have requirement of 20k users,in which there are 10k CUC & IM users,,,which hardware i can go for UCS-C series or B-series,can i install all the servers in a single box?
Sip trunk between callmangers 8.5 - 10.5. calls work fine. But when we call from 10.5 side the other end is not getting calling name. it is getting the calling number. when I do a Sip trace, I see that 10.5 is not sending calling name in the invite.W...
Hello everyone,I've got a very vexing issue. I converted a router over from MGCP to h.323. IOS Advanced IP Services 12.4-4(t). With MGCP there was never an issue with dropped calls. Ever since switching gateway over to h.323, any calls are droppe...
Hi All, As per the pre-upgrade tasks, the Extension Mobility service needs to be stopped before starting the upgrade. It seems the only service that highlighted before system upgrade. But what's the reason behind that? Regards,Gary
Hello,i can't control 8961 phone (SIP) with jabber.I can control IP Communicator and Cisco 6945, so i think the configuration is fine.I also tried adding:Standard CTI Allow Control of Phones supporting Connected Xfer and conf (89xx/99xx-phones)Standa...
In case of upgrading Cisco call manager 3.3 version,as i know that with ics 7750 we can upgrade to the version 4.0,my question after upgrading 4.x to go latest version how migration happens ?what steps i need to follow? is it possible we can upgrade ...
Hi,I have a router (IOS 15.2) running MGCP have caller-id enabled on our gateway and as well in CUCM. (10.5) I have this configuration for the ports and dial-peers. voice-port 0/0/0 cptone TR timing hookflash-out 50 timing guard-out 1000 caller-id ...
Hello,We have a Cisco 3925 configured with CME 7 and enabled with the UC module. The machine also has a PRI and some BRI cards.Is the following possible; a ISDN call comes in the Cisco 3925 (does not hit CME yet), the call is routed to our SIP platfo...
Hello, Im new with CCX and I can see that in the list of servers the status for the servers I have are in "PARTIAL SERVICE ". Any idea what I can check? or this is normal? Thanks
Hi all ,we have a pilot number for help desk for which we have 3 extensions in a line group , when no answered or busy call will hit voice mail . we have added a new extension to group , calls lands on phone in order mentioned in group but voice mail...
Hi All cisco 7821 is configured with 8 speed dials however when you hit the down button it wil lonely show the first 6 ? anyone have a resolution ? You can still dial the 7/8th speed dials but you cannot view them with the button (pressing down on t...
Hi One single router and single isdn line , now added one more router and another isdn line created a css named ' gateway_secondary ' and a partition created ' gateway_secondary ' and the partition added to the css .There are phones which is under...
We are running CUCM 8.6 with one publisher and two subscribers. One of the subscribers has failed and we are now running off only one subscriber. In this mode, we are experiencing a number of minor problems with the phones including:Time on handsets ...
| User | Count |
|---|---|
| 8 | |
| 4 | |
| 3 | |
| 1 | |
| 1 |
