Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
hello every one i ask if i could disactivate the 1 st network card because I'm installing a CUCM registrerd with the 2nd card.if so how i can do it. Best Regards
I would appreciate if anyone can tell me how to turn off of the message indicator light after you have listen to voice mail messages. Currently, you need to do something with the message (like save, move or delete) before MWI turns off. In our old ...
Hi, I running Lync 2010 on CISCO SBA, the inbound call fails when the WAN link is down, outbound call works fine. any help or pointer will be appreciated.
Hello,I have an question is kind stupid, but somebody asked me and i have this doubt too. If i have pc attached to my phone, but i onle have one vlan, the IP Phone and the PC will work? I know that we can face some problems with this scenario. Regard...
Hello, Got a strange one here. So I have an E.164 dial-plan setup but now all of a sudden the call stored in the placed calls directory only is not saved in e.164 919803338412 -> tran pattern to +19803338412 -> RP \+! -> SIP Trunk -> Called Party ...
Hi,I have 3 CUCM in 1 group, 2 nos in HO and 1 no's in DR and in DHCP option 150 contains pub and sub1,sub2, but the IP phone is capable of accepting only 2 tftp, if incase of my pub,sub1 fails ip phones shld failover to sub2 without changing the opt...
Hello Guys.. I've been configuring an AA on a Cisco Unified CM BE6K. I created the call handlers, the greetings. I created and extension and I fowarded all calls to the voice mail. I also created a CTI route point and assign the forwarded extension t...
Hello everyone!I stumbled upon a rather strange behavior on a CP-7942G IP phone. It is a new phone, which I have myself unpacked from the box, along with 2 others.Now, the problem is, this particular phone did not load the user-locale, specified in t...
Hi all,Had this interoperability between Cisco 2811 E1 PRI with DMS100, because Nortel Opc 11C´s E1 Card does not support Net 5 or QSIG, so it is used DMS100 instead. All the Channels go UP on both PBX and Router, but when try to dial a number to t...
Hi to all One request came from a client , i believe its not possible but pls share your thoughts Scenario:111 extension is configured when no answer( CFNA) sending the call to 222Now we need when the call arrive to 222 and if 222 no answer then th...
Hi,Currently I setup a phone as pilot number and if no answer, it will forward the call to hunt group, in this hunt group it have 5 IP Phone and I using broadcast method to ring all phone. If all IP Phone in hunt group does not answer the call, it wi...
Hi we are using CUCM 9.1 and extension mobility. Users are synced to the LDAP Directory. Users are comming and leaving as it is usual in big firms.Now I have got the problem that the users aren´t deleted in LDAP immediatly after they have left the co...
Hi Everyone, As my subject above,I want to set my VCS Expressway's Authentication to use Local Database,So all user (either H323 and SIP) must have valid username and password to do registration with my VCS Expressway,In Cisco's guide Cisco_VCS_Auth...
Hi all, I have to upgrade a CUCM actually in use from 6.1 on MCS 7828 to CUCM 9.1 on VMWARE ( Business Edition on UCS C220). I want to know what is the best scenario to do for the upgrade? thanks in advance regards Cham
Hello, I`ve got a CUCM 9.1.2 connected via SIP Trunk to two other PBX. When I have a call between two CUCM Phones (eg. DN 2001 calls 2002) and I start a transfer from DN 2002 to 5001 (on 3rd Party PBX) the number (and name) 2002 is signalled on call...
| User | Count |
|---|---|
| 6 | |
| 6 | |
| 5 | |
| 4 | |
| 3 |
.jpg "VIP Expert"){kind=icon}
