Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear Cisco techs,Can someone please guide me to link on how to set up TFTP on 2691 routerWhen I type conf t.tttp-server flash: is does nothingOr tftp-server gives unrecognized commandHave searched quite a few places. Leads to various links but nothin...
i was trying to change the ip phone from sccp to sip, and when i tried was this one in this link:http://www.mehrdust.com/archives/cisco-ip-phones-79xx-with-asteriskand i used the files on download here:http://www.mehrdust.com/downloads/7911-SIP-P0S3-...
Hi there!Can i make a cisco 7911 sip enable, and integrate it with 3rd party pbx software?let me know.Regards!
Hello,I have Cisco IP Phone 7821.Can anybody can tell me where I can set up time - which is now 2sec - from dialing a number on the phone to hear a signal ? In Phone ver. 6921 call has been done immediately.I am working with UCCE 9Thanks for help!
HI, We have call manager cluster 8.6 version and there are 5 nodes in the cluster. I could see CDR files generated in the subscriber nodes but it is not uploaded publisher node CDR repository . I am not seeing any CDR files in Publisher preserve fold...
Hi, i have an Telephony setup with CME 2921 router with 15.X software version. I need to configure the SIP Bind command under the voice service voip. bind control source-interface FastEthernet 0/0 But when I am configuring I getting the error. ...
I have a router 2911 and I want to configure jabber to android smartphone ? What write in the device name ? I really appreciate your help. Thank you.
We have 4 T1 PRI's coming into our router. I've had complaints on the floor that random people get dropped calls, or where the other end can't hear them, and dial tones everytime they talk. I've called my own number numerous times and noticed that ...
I'm requesting assistance on the following issue. I have an h323 gateway that I'm using in a trunk group with 4 lines.The issue I'm having is if I unplug the cable from line 1 and place an outbound call, it tries to go out of line 1 and I get a busy...
We had a user (user1) with ext 6000, they left the company and a new user (user2) came in. We were unable to delete the user through gui, we did it through cli. Now when someone calls 6000 it doesn't go to user2's vm mailbox, instead we here user1'...
How Configure Call Waiting phone cisco 6941?
Hi I need 30 unit license for Cisco Communication Manager 7.1. But I found that it's already end of sale. I want the unit license part number for cisco cucm 7.1.3 version. And i found revised part numbers for user license (CUCM-USR-LIC ) but those ...
Hello,I do not deal with this often so want to make sure my logic makes sense. I have a site that currently has 2 Bogen AMP's and a Bogen NR100. They are using the NR100 for paging. So they can dial a 5 digit extension to page over their existing ...
I am trying to set up a 9971 with plar, ring down, to a hunt pilot. The cisoc doc is not clear to me at all. is the only thing I need is a sip dial rule?How does that look? again, the cisco doc is not adequate explanation for me, i am not getting it....
Hi,I've been doing some research in trying to find good tool that can retrieve configurations (like CSS, Partitions, regions, device pools etc.) from CUCM. i know this may be a third party tool. Dose anyone have any ideas? Thanks,Surendra
| User | Count |
|---|---|
| 6 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
