Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Community.This is my SIP Phone config:voice register dn 2number 214name xxxno-reglabel xxxvoice register pool 2id mac 44E4.D944.9B11session-transport tcptype 9971number 1 dn 2number 2 dn 3dtmf-relay rtp-nteusername xxx password xxxcodec g711u...
I'm upgrading a server to 8.6 and i've installed ciscocm.refresh_upgrade_v1.1.cop.sgn.These were the last couple lines from the console:02/23/2012 23:08:48 killing copstart.sh pid=3180902/23/2012 23:08:48 Waiting for CLI/GUI to show cop install suc...
Is there any way to make CIPC supported IPv6??
Since upgrading to CUCM 7.1.3.10000-11 any new phone plugged into the system gets an "auth fail" from the TFTP server when attempting to upgrade the firmware to the version that comes with 7.1(3). Phones that were registered prior to the upgrade wor...
Hi,How do I tell if my router is recognizing the VIC-2FXO-M1 card I put in it? I want to confirm the card is working, but I don't know how to tell if it is working or recognized since I purchased it used.Thanks,Mitch
Hi,Does any one know the application of the Called Party Transformation Mask CSS within the Device Mobility Section of the Device Pool Configuration? Page 604 on the Collab SRND 9.x states it has no impact on phones not sure what this really means if...
I am trying to bring up a test CME 8.6 server, but am having issues getting my test IP7941G phone to register with the system. The phone definitely gets an IP address from the CME server, but it looks like the problem is that it's not getting its ap...
I Have a client requirement in which they want the following:1. implement the central site with BE 6000, and "n" number of remote sites with "CME", after the IP WAN connectivity is done in the near future, they want the CMEs to convert ...
HI Engineerswe have access door system and also cucm 8.6 ...the question is can we open the door through our ip phone ????Regardsahmed bahala
I have an older Cisco 2921 ISR that was recently upgraded to the following software versions:IOS: 15.1(4)M7CME: 8.6CUE: 7.0.6However, I don't think the CME files on the flash were appropriately upgraded. Just the IOS version.Where would I find the a...
I have a 2821 ISR router running CME 8.6, but I appear to be missing something in the configuration because the first test phone that I am attempting to connect to the system is hanging at "Registering". It's getting a DHCP address from the server, ...
I've been scouring the CUPS documents to try to find the maximum number of users supported per server. But I've failed to find a simple table that says server type X supports Y users. (I understand that there are differences between the deployment me...
I need response below query:Requires Singapore users to make tail drop calls (with CLI) to Thailand Gateway for PSTN breakout to Thailand suppliers. If suppliers return call, call should reach Singapore users with CLI displayed.Please advise me how t...
Hello,Seems like most people these days are using flash as the location of their CME phone firmware, config files, GUI, rintones, etc.However if you dont need to do locals per phone or phone type, what are the benefits of using flash: versus system: ...
Hi All,I have two questions regarding Cisco Unified Presence.I have installed CUPS 9.1 in our CUCM 9.1 environment.All call control, calendering and IM works fine with both CUPC and Jabber ClientsWe would like to open our presence server up to be all...
| User | Count |
|---|---|
| 7 | |
| 4 | |
| 2 | |
| 2 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
